Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Alto-Shaam Dateigröße: 489.71 kb Dateiname: BUFFETCART.pdf Unterrichtssprache:

For commercial use, the product is warranteed for a period of 90 days. During this period, Equator Corporation will provide all labor and parts necessary to correct such defect, free of charge, if the appliance has been installed and operated in accordance with Equator Corporation’s written instructions with the appliance. Ready access to the appliance, for service, is the responsibility of the consumer-owner. EXCLUSIONS In no event shall Equator Corporation be liable for incidental or consequential damages or for damages resulting from external causes such as abuse, misuse, incorrect voltage or acts God. This warranty does not cover service calls which do not involve defective workmanship or materials covered by this warranty. Accordingly, diagnosis and repair costs for a service call which does not involve defective workmanship or materials will be the responsibility of the consumer-owner. Specifically, the following work is not covered under warranty and does not constitute warranty work: . Installation -e.g. improper hook-up or leveling . Maintenance -e.g. cleaning of air and/or water filter . Damage -e.g. Replacing broken door handle Most work is covered. The defining factor is, has the machine malfunctioned (Equator is responsible) or has the customer omitted or done something to cause machine to malfunction (customer is responsible). Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. 1 WARRANTY SERVICE This warranty is given by: Equator Corporation, Equator Plaza, 2801 W. Sam Houston Pkwy. N., Houston, TX 77043-1611. Service under this warranty must be obtained by the following steps, in order: Call an Equator Corporation Authorized Service Agent (obtain number of nearest agent from your dealer or by calling Equator Service at 1-800-776-3538). Under normal circumstances, Service will be provided during regular business hours (9:00 a.m. to 5:00 p.m. weekdays). GENERAL Since it is responsibility of the consumer-owner to establish the warranty period by verifying the original purchase date, Equator Corporation recommends that a receipt, delivery slip or some other appropriate payment record be kept for that purpose. Remember to send in your Warranty Registration Card so that a proof of your purchase exists with Equator. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. Corporate Office EQUATOR CORPORATION Equator Plaza 2801 W. Sam Houston Pkwy. N. Houston, TX 77043-1611 Tel: 713-464-3422 -Fax: 713-464-2151 Tel: 800-776-3538 DISASSEMBLY AND ASSEMBLY ENSURE APPLIANCE IS DISCONNECTED FROM THE ELECTRICITY SUPPLY BEFORE DISASSEMBLING. NOTE ALL CONNECTION DETAILS AND ROUTING OF LEADS BEFORE DISASSEMBLING. Numbers appearing in the text rater to illustrations and parts list numbers. A. SLIDING TABLETOPS Slide both tabletops open. Remove cover caps 130 end the two screws securing handle 105. Withdraw the handle from the tabletop assembly. Slide the tabletop required inwards, past its closed position, until the two plastic sliding blocks 106 on the cabinet channels are exposed. Withdraw the sliding blocks from the cabinet channels, and than slide the tabletop assembly out clear of the channels. B. DOORS 1. Remove both sliding tabletops completely (see A.1.) and magnetic door catches 111 (push-fit). 2. Drill out the rivet at each end of the front slide channel using a 3mm bit. Use extreme care when drifting. Withdraw leg top caps 108, then remove front top panel 109 to release top door pivots 128. Lift doors 123 and 125 clear of the cabinet. C. TOP ELEMENT ASSEMBLY 1. From Inside of cabinet, squeeze locking barbs and release mains lead bush 121 retainer from rear panel. Remove rear cover strip 510, secured by a single screw, to the extant of the mains lead wires. Disconnect the top element leads from terminal block 120. NOTE: Terminal block 120 Includes push-in locking terminals for internal wiring. Leads inserted in the front-most terminals may only be released by inserting & small screwdriver or similar in the slots provided in the front of the terminal block. Rear-most leads may release with a sharp pull. If leads cannot be released, or are not gripped on insertion, item 120 must be replaced. 2. Open the sliding tabletops and remove glass dishes and lids 101 and holders 103. 3. Remove the sliding tabletops as in A. 1. Then slide each tabletop in turn inwards past its closed position to gain access to the four screws securing top element assembly 107. 4. Use a powerful magnet or suitable tool to lift the element assembly out clear of t...

Herunterladen

Geben Sie zwei Ziffern: