Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
The recommended length of time to keep bread dough in the Warmer Drawer is about 45-60 minutes. Be sure however to follow the recipe’s recommended times. The unrisen bread dough should be placed in a large bowl since the dough will nearly double in volume. Place the Warmer Drawer Rack in the downward position (see Figure 3). Before placing in the Warmer Drawer, cover the bowl with a moist cloth or use wax paper that has been coated with a non-stick type cooking spray. NOTE : The bread proof function uses low warming temperature which could happen to be lower than your room temperature. The drawer will not work as a cooling device and will not be able to lower the temperature under the ambient temperature. To Set the Humidity Controller The humidity controller is located on the inside of the warmer drawer and used to control humidity in the warmer drawer. The humidity control knob can be set at any position between Moist (Figure 1) and Crispy (Figure 2) position. To set the humidity controller, slide the humidity control knob to the desired location. Figure 1 Figure 2 General Care & Cleaning 9 TO REMOVE AND REPLACE WARMER DRAWER ! WARNINGWARNINGWARNINGWARNINGWARNING Turn the warmer drawer to OFF before removing the drawer. DO NOT touch the warmer drawer element. The element may still be hot enough to cause burns, even if it is dark in color. To Remove Warmer Drawer: 1. Turn power off before removing the warmer drawer. 2. Open the drawer to the fully opened position. 3. Locate glide lever on each side of drawer, pull up on the right glide lever and push down on the left glide lever (See Figure 1). 4. Pull the drawer away from the range. To Replace Warmer (Warm & Ready™) Drawer: 1. Pull the plastic slider to the front of the glide slots on each side of the drawer cavity (See Figure 2). 2. Align the glide on each side of the drawer with the drawer cavity glide slot. 3. Push the drawer into the drawer cavity until glide levers “click” (approximately 2”). If you do not hear the glide levers “click” or the drawer does not feel seated remove the drawer and repeat steps 1 thru 3. ! WARNING WARNINGWARNINGWARNINGWARNINGWARNING Electrical Shock Hazard can occur and result in serious injury or death. Disconnect appliance from electric power before cleaning and servicing the warmer drawer. Left glide Pull up lever with finger Figure 1 Lever Lever Right glide Pull down lever with finger Figure 2 10 General Care & Cleaning CARE & CLEANING TABLE Cleaning Various Parts or Your Appliance Before cleaning any part of the drawer, be sure control is turned OFF and the drawer is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANINGS WILL REDUCE THE NUMBER OF MAJOR CLEANINGS LATER. Surfaces How to Clean Plastic Membrane Keypad Clean with a cloth soaked in soapy water. Rinse with a clean water and a dishcloth. Note: Humidity controller knob can not be removed . Stainless Steel Door & Drawer Body Cleaners made especially for stainless steel are recommended. Always follow the manufacturer's instructions. Be sure to rinse the cleaners. DO NOT clean the door gasket. The door gasket is essential for a good seal. Care should be taken not to rub, damage or remove the gasket. Porcelain Enamel Body Parts and Cavity Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of clear water and ammonia. If necessary, cover difficult spots with an ammonia-soaked paper towel for 30 to 40 minutes. Rinse with clean water and a damp cloth, and then scrub with a soap-filled scouring pad. Rinse and wipe dry with a clean cloth. Remove all cleaners or the porcelain may become damaged during future heating. DO NOT use spray oven cleaners. Warmer Drawer Rack The rack may be removed for cleaning. Clean by using a mild, abrasive cleaner following manufacturer's instructions. Rinse with clean water and dry. Solutions to Common Problems 11 IMPOR IMPORIMPORIMPORIMPORIMPORT TTTTTANT ANTANTANTANTANT Before calling for service, review this list. It may save you both time and expense. This list includes common experiences that are not the result of defective workmanship or material in your Warm & Serve Drawer. DRAWER IS NOT LEVEL • Poor installation. Place a level on the cutout bottom. Make sure bottom is level. • Be sure cutout bottom is strong and stable enough to adequately support drawer (and wall oven, if applicable). CANNOT MOVE APPLIANCE EASILY • Appliance must be accessible for service. • Cabinets not square or are built in too tightly. Contact builder or installer to make appliance accessible. WARMER DRAWER DOES NOT OPERATE • Make sure cord/plug is plugged tightly into outlet. • Service wiring is not complete. Contact your dealer, installing agent or authorized servicer. • Power outage. Check house lights to be sure. Call your local electric company for service. 12 Warranty Information WARMER DRAWER WARRANTY Your warmer drawer is protected by this warranty In the U.S.A., your appliance is warrante...