Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
3.0 Gallon TITAN TF SERVER INTRODUCTION This server is intended for use with a BUNN® TITAN DUAL, or TITAN SINGLE coffee brewer only. When proper precautions are followed, 1.5 to 3.0 gallons of coffee may be brewed directly into the server and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf. USER NOTICES The notices on this server should be kept in good condition. Replace unreadable or damaged labels. #26186.0000 DAILY CLEANING CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing solution using an approved non-chlorine sanitizer. Do not submerge server. 1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server completely by opening the faucet. 2. Remove the lid, fill server with cleaning solution and thoroughly clean the inside of server. 3. Rinse server thoroughly using fresh water rinse. 4. Fully fill server with sanitizing solution for 5 minutes then drain through fully open faucet. 5. Remove the faucet handle/stem assembly by unscrewing the faucet nut just behind the faucet handle. 6. Use enclosed cleaning brush to thoroughly clean the faucet spout and connector. 7. Remove the cap, sight gauge tube and washers. 8. Use enclosed cleaning brush to thoroughly clean the fill tube of the lid assembly and sight gauge tube. 9. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts and lid in a mild detergent and water solution. Rinse the parts in hot water. Sanitize the parts for five minutes, then air dry completely. 10. Reassemble the faucet/stem assembly and attach it to the faucet. 11. Install the sight gauge tube and washers in the shroud and secure with the shroud cap. 12. Wash the entire outside surface of the server with a clean damp cloth. 40359 082807 2 3 18. 26186.0000 Decal, Warning Hot Liquid 19. 40097.0001 Spacer 20. 32591.1000 Tube, Silicone .50" I.D. x 2.0"(Cut to length) 21. 12422.0001 Clamp, Tube .59"/.66" I.D. 22. 39543.0001 Guard, Faucet 23 12422.0012 Clamp, Tube .81"/.97" I.D. 24. 40271.1100 Cover, Bottom 45279.0000 Screw, Pan Head #8-32 x .25" 25. 01221.0000 C-Ring, Faucet Shank 26. 03093.0002 Wing Nut, Faucet 27. 26685.0000 Faucet Assy, Bunn Handle 26685.0003 Faucet Assy, Plain Black Handle 28 26684.0000* Faucet Handle, Bunn 07096.0007* Faucet Handle, Plain black 29. 29165.0001* Faucet Bonnet 30. - - - - - - - - * Faucet Body (Not available. Order item 27) 31. 35301.0000 Brush, Cleaning (Not Illustrated) * Component of item 27 6172 3 4 8 5 8 15 14 9 16-17 18 19 22 21 20 23 24 SERVER P3896 13 12 11 10 40359 110211 28 29 11 12 13 30 15 25 26 27 Vertical Faucet REPLACEMENT PARTS 1. 39542.1000 Shroud, Sight Gauge (Includes Item 4) 2. 35010.0000 Plate, Decal Mounting 3. 35009.0000 Decal, Bunn 35009.0001 Decal, Plain Black 4. 35004.0002 Backing, Sight Gauge 3.0 Gal. 5. 35005.0003 Sight Gauge Tube 3.0 Gal. 6. 39083.0000 Cap, Shroud 7. 02367.0000 Screw, Truss Head #6-32 x .62" 8. 39143.0001 Washer, Sight Gauge Tube 9. 39081.0000 Handle, Faucet, Bunn (Horizontal Faucet) 10. 35003.0000 Nut, Faucet Spout (Horizontal Faucet) 11. 00601.0000* Faucet Spring 12. 29164.0000* Faucet Stem 13. 00600.0000* Faucet Seat Cup 14. 35074.0000 Screw, Hex Hd Black M4 x .7x25 15. 40132.0000 Spout, Faucet (Horizontal Faucet) 41159.0001 Shank, Faucet (Vertical Faucet) 16. 39487.1000 Lid Assembly 3.0 Gal. (Includes item 17) 17. 40106.0000 Cap Assembly BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor. 2) All other equipment -2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years. b) Compressors on refrigeration equipment - 5 years parts and 1 year labor. c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and labor for 4 years or 40,000 pounds of coffee, whichever comes first. These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality, damage or casualty. In addi...