Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Kuppersbusch USA Dateigröße: 377.65 kb Dateiname: Unterrichtssprache:

The ends of the strips must fit together without overlapping. -Evenly and securely fix the seal to the hot plate, pressing into place with the fingers and removethe strip of protective paper from the seal and setthe plate into the hole made in the cabinet. -Fix the hob with the proper brackets “S” and fitthe prominent part into the porthole “H” on the bottom; turn the screw “F” until the bracket “S” stick on the top (fig. 7). -The prospective walls (left or right) that exceed the working table in height must be at a minimum distance from the cutting as mentionned both inthe columns and the scheme. -In order to avoid accidental touch with the overheating bottom of the hob, during the working, is necessary to put a wooden insert, fixed by screws, at a minimum distance of150 mm from the lower surface of the top (see fig. 4). COMPLY WITH THE DIMENSIONS(in mm) A B C D E 4F (60) 553 473 67.5 59.5 100 min. 5F (90) 833 475 67.5 62.5 73.5 min. FIG. 4 FIG. 5 FIG. 6 FIG. 7 7 INSTALLATION 6) ROOM VENTILATION To ensure correct operation of the appliance, it isimportant to ensure that the room where the hotplate is installed has sufficient ventilation. 7) GAS CONNECTION NaturalGasandPropaneGas Natural Gas installations require the connection ofa gas regulator at the appliance. This regulator issupplied with the appliance on purchase. Assemble the regulator (noting the gas flow direction) and transition pieces (supplied with theappliance), in accordance with below figure. The transition piece on the supply side of the regulator must be provided by the installer. Unions compatible with the hose fittings must be used and connections tested for gas leaks. Ensure the supply connection point is accessible with the appliance installed. Warning: ensure that the hose assembly is restrained from accidental contact with the flue or flue outlet of an underbench oven. 8 INSTALLATION 8) ELECTRICAL CONNECTION The electrical connections of the appliance must be carried out in compliance with the provisionsandstandards inforce. Before connecting the appliance, check that: -the electrical capacity of the mains supply and current sockets suit the maximum power rating of the appliance (consult the data label applied to the underside of the hot plate). -The socket or system has an efficient earth connection in compliance with the provisions and standards in force. The manufacturer declines all responsibility for failing to comply with these provisions. When the appliance is connected to the electricitymainbyasocket: -fit a standard plug suited to the load indicated on the data label to the cable. -Fit the wires following figure 8, taking care of respecting the following correspondences: LetterL(live) = wire; LetterN(neutral) = wire; earthsymbol = greenoryellow-greenwire. -Never use reductions, adapters of shunts for connection since these could create false contacts and lead to dangerous overheating. -The outlet must be accessible after the built-in. When the appliance is connected straight to the electricitymain: -install an omnipolar circuit-breaker between the appliance and the electricity main. This circuit- breaker should be sized, in compliance with current installation regulations. -Remember that the earth wire must not be interrupted by the circuit-breaker. -For optimum safety, the electrical connection may also be protected by a high sensitivity differential circuit-breaker. You are strongly advised to fix the relative yellow- green earth wire to an efficient earthing system. FIG.8 9 INSTALLATION 9) FIXING THE WORKTOP The hot plate has a special seal which prevents liquid from infiltrating into the cabinet. Strictly comply with the following instructions in order to correctly apply this seal: -detach the seals from their backing, checking that the transparent protection still adheres to the seal itself. -Overturn the hot plate and correctly position seal “E” (fig. 6) under the edge of the hot plate itself, so that the outer side of the seal perfectly matches the outer perimetral edge of the hot plate. The ends of the strips must fit together without overlapping. -Evenly and securely fix the seal to the hot plate, pressing into place with the fingers and remove the strip of protective paper from the seal and set the plate into the hole made in the cabinet. -Fix the hob with the proper brackets “S” and fit the prominent part into the porthole “H” on the bottom; turn the screw “F” until the bracket “S” stick on the top (fig. 7). -The prospective walls (left or right) that exceed the working table in height must be at a minimum distance from the cutting as mentionned both inthe columns and the scheme. -In order to avoid accidental touch with the overheating bottom of the hob, during the working, is necessary to put a wooden insert, fixed by screws, at a minimum distance of 60 mm from the lower surface of the top (see fig. 4). 10 ADJUSTMENTS Always disconnect the appliance from the electricitymainbeforemakinganyadjustments. All seals mus...

Herunterladen

Geben Sie zwei Ziffern: