Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: GE Dateigröße: 329.53 kb Dateiname: Unterrichtssprache:

Frequency of cleaning depends on water hardness. With hard water (15 to 20 grains/gal. [4 to 5 grains/liter]), cleaning may be required as frequently as every 6 months. For best performance, brush or vacuum lint and dirt from the condenser once a year. Unscrew the grille on the bottom front of the cabinet to access the condenser. Exterior surfaces Wash the exterior enamel surfaces and gaskets with warm water and mild soap or detergent. Wipe and dry. Regular use of a good household appliance cleaner and wax will help protect the finish. Do not use abrasive cleaners on enamel surfaces as they may scratch the finish. Models with a stainless steel exterior can be cleaned with a commercially available stainless steel cleaner using a clean, soft cloth. Do not use appliance wax or polish on the stainless steel. Icemaker system 1. Push the selector switch to OFF. 2. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove all ice from the storage bin. 3. Unscrew the drain cap from the bottom of the water pan located inside the storage bin as shown. Allow the water to drain completely. Drain cap Water pan 4. Replace the drain cap. 5. Use one 16 oz. bottle of Nickel Safe Ice Machine Cleaner by Nu Calgon. Read and follow all safety precautions on the bottle. Pour one bottle of solution into the water reservoir. Fill the bottle twice with tap water and pour it into the water reservoir. Nickel Safe Ice Machine Cleaner by Nu Calgon is available at appliance repair shops, or through GE Parts and Accessories. Order part number WX08X42870. In the U.S.A., call 800.626.2002 or visit GEAppliances.com. In Canada, call 1.888.880.3030. 6. Push the selector switch to CLEAN. The light will turn on, indicating that the cleaning cycle is in process. 7. When the indicator light turns off (approximately 45 minutes), the cleaning cycle is complete. During the cleaning cycle, the system will both clean and rinse itself. 8. After the cleaning cycle is complete, remove the drain cap from the water pan to see if any cleaning solution is left in the water pan. If cleaning solution drains from the water pan, you should run the clean cycle again. NOTE: Severe scale buildup may require repeated cleaning with a fresh quantity of cleaning solution. 9. Push the selector switch to ON to resume ice production. Care and Cleaning Icemaker Condenser A dirty or clogged condenser: 4. Remove dirt and lint from the condenser • Prevents proper airflow. fins and the unit compartment with a brush attachment attached to a vacuum cleaner. • Reduces ice making capacity. • Causes higher than recommended operating temperatures which may lead to component failure. 1. Unplug the icemaker or disconnect power. 2. Remove the 2 screws in the lower access panel and the 2 screws from the base grille area of the front panel support. Pull forward to remove the lower access panel. 3. Pull the bottom forward and then pull down to remove the lower access panel. 5. Replace the lower access panel using the 4 screws. 6. Plug in the icemaker or reconnect power. Care and Cleaning Icemaker Interior 1. Unplug the icemaker or disconnect power. 2. Open the storage bin door and remove any ice that is in the bin. 3. Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap. 4. Remove the three screws that hold the cutter grid cover in place. 5. Unplug the wiring harness from the left side of the cutter grid. Cutter grid cover Screws 6. Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid. 7. Remove the right-hand screw and loosen the left-hand screw. Lift the cutter grid up and out over the left-hand screw. NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid. OFF ON CLEAN Wiring harness Cutter grid Ice level sensor Screw Plastic spacer Screw 8. Remove the two screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side. 9. The cutter grid, exterior of hoses, water pan, storage bin, door gasket and ice scoop should be cleaned with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tablespoon (15 mL) of household bleach in 1 gallon (3.8 L) warm water. Rinse again thoroughly in clean water. NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand high temperatures. 10. Wash only the outside of the plastic hoses with mild soap or detergent and warm water. Rinse with clean water. 11. Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws. 12. Check the following: • Drain cap from the water pan is in place. • Hose from the water pan is inserted into the storage bin drain opening. 13. Slide the cutter grid back into place and secure it by replacing the right-hand...

Herunterladen

Geben Sie zwei Ziffern: