Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Avanti Dateigröße: 272.19 kb Dateiname: Unterrichtssprache:

IF THE POWER CORD IS DAMAGED, HAVE IT REPLACED BY AN AUTHORIZED AVANTI PRODUCTS SERVICE CENTER. ? This ice maker should be properly grounded for your safety. The power cord of this ice maker is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock. ? Do not under any circumstances cut or remove the third ground prong from the power cord supplied. ? Never use an extension cord to connect power to the unit. ? Never use a two -prong grounding ad apter. ? Where a two-prong wall receptacle is encountered, contact a qualified electrician to have it replaced with a 3-prong receptacle in accordance with applicable electrical codes. ? This ice maker requires a standard 115/120 volts a.c.~/60hz electrical outlet with three -prong ground. ? The cord should be secured behind the ice maker and not left exposed or dangling to prevent accidental injury. • Extension cord Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this appliance. However, if you must use an extension cord it is absolutely necessary that it be a UL/CUL -listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes. OPERATING YOUR ICE MAKER • Control Panel Operation Start Press to turn unit on. This button is also used to start the ice making cycle. Stop Press to turn unit off. Select ICE SIZE SELECTION of (S) small, (M) medium or (L) large. (The chosen mode shall stay as selected unless changed or there is a power failure). Please select the (S) when ambient temperature is below 15°C (59.F). Alert ADD WATER INDICATOR. The ”Alert ” light will come on with a beep sound. Add water and press “STOP” button and then press “START” button to restart the icemaker. Ice Full ICE FULL INDICATOR. This light will come on with a beep sound which indicates that the storage cabinet is full. Press the “STOP” button and remove the ice cubes then, press the “START” button to restart the Ice maker. IMPORTANT: YOU MUST PRESS “STOP”. THEN THE “START” BUTTON TO RESTART THE ICE MAKER AFTER YOU ADD WATER OR REMOVE SOME OF THE ICE CUBES. 10 Operating Instructions Starting your Ice maker ? Open the lid and fill the reservoir with water. Make sure the water level in the reservoir is not over the Ice collecting tray. ? Press START button to turn unit on. ? Select desired ice cube size by pressing “ice size” selectors S, M and L. ? Check the water level in the reservoir periodically. The ice maker will detect any shortage of water and stop operating. The ALERT indicator will be lit. Press the STOP button and fill the reservoir with water. Wait 3 minutes after the ALERT light goes out and then press the START button. The Ice maker will begin operation. ? When the ice cubes are collected and reaches the bin sensor, the ice maker will stop operating and the ICE FULL indicator will be lit. ? There are three sizes of ice cubes available, therefore the larger the ice cube selected, the longer the time it will take to complete the cycle. When the ambient temperature is lower than 15°C (59.F), the small or medium ice cubes sizes are recommended to avoid ice cubes clumping together. ? For best performance, water temperature should be between 7°C (45.F) and 35°C (95.F) and ambient between 15°C (59.F) and 25°C (77.F). CARE AND MAINTENANCE • Cleaning Your Ice Maker ? To ensure the cleanliness of the ice cubes, water in the reservoir should be replaced every 24 hours. ? If the compressor stops for any reason such as water shortage, too much Ice, power off, etc... Do not start the system right away, wait 3 minutes, and then re -start the Ice maker. ? Remove the drain plug to drain remaining water from the water reservoir when the ice maker will not be used for long period of time. Screw the drain plug back in place after the water has been drained. ? Always change with fresh water before starting ice production at initial installation or after long shut-off periods. ? Please clean your Ice maker regularly. When cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inside and the outside surface of the Ice maker. Do not spray Ice maker with chemicals or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting. Caution Failure to unplug the ice maker could result in electrical shock or personal injury. • Space Requirements ? During transportation, the incline angle of the cabinet should not be over 45° ? Do not turn the Ice maker upside down. Problems could occur in the compressor and sealed system. ? The Ice maker should be placed horizontally on a properly leveled surface. ? To ensure proper ventilation for your Ice maker allow 6” of space at the top, the back and on each side. ? Before using the Ice maker for the first time, please wait 2 hours after...

Herunterladen

Geben Sie zwei Ziffern: