Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: DCS Dateigröße: 237.95 kb Dateiname: Unterrichtssprache:

By rotating the dial clockwise to the high position, the drawer will reach a temperature of approximately 230°F. To Use: Turn the thermostat dial to a temperature setting; High Medium Low Proofing ■ If you will be using the tray, preheat it while preheating the warming drawer. ■ Preheat any empty serving dishes to be used, while preheating the drawer. ■ Add cooked, hot food in its cooking container or heat-safe container. ■ Aluminum foil may be used to cover food containers. _CAUTION Do not use plastic containers or plastic wrap. They can melt if in direct contact with the drawer or a hot utensil and if these items melt, they may adhere to the drawer and may be unremovable. Use only heat-safe dishes. PREHEAT TIME AND TEMPERATURE SELECTOR: Proofing.....Do not preheat 90°-110° Low..............Preheat 10 min. 140°-170° Medium ....Preheat 15 min. 170°-200° High............Preheat 20 min. 200°-230° ■ Always preheat on high, then turn the knob to the desired setting. ■ To keep several different foods hot together, set the temperature to the food needing the highest setting. Place items needing highest setting on the bottom of the drawer and food needing less heat on the tray. PROOFING YEAST DOUGH Place dough in a greased jelly roll or half sheet pan or oiled bowl, no taller than five inches in height. Turn dough over to grease all areas of the dough,cover with a damp clean cloth. Place in the center of warming drawer and turn the control knob to LOW and immediately back to PROOF. Check at 45 minutes to one hour. Dough should double in size. Shape dough, place in baking pan, and put in warming drawer for second rising, about 30 to 45 minutes; add extra time if needed. Fig. 07 S USE & CARE INFORMATION CLEANING THE WARMING DRAWER ■ Be careful cleaning any part of this appliance, particularly the drawer box and back of the drawer face. All parts of the drawer can be cleaned with a hot soapy damp cloth,rinsed,dried and buffed with a heavy pile cloth. Always try this first,as it is the mildest cleaning procedure. ■ Be sure the Warming Drawer is turned off and the appliance is cool before using any type of aerosol cleaner on or around the appliance. The chemical that produces the spraying action could, in the presence of heat, ignite or cause metal parts to corrode. ■ Use the mildest cleaning procedure first. Some brands of cleaners are harsher than others, read their directions. Try on a small area first. ■ To avoid marring the surface always rub the metal finishes in the direction of the polish grain lines. The cleaner will be more effective when used in the direction of the polish lines. ■ Use only clean sponges, soft cloths, paper towels, plastic or non-metal soap pads for cleaning or scouring, as recommended in this section. (Caution: some soap pads can scratch). ■ Be sure to rinse all parts thoroughly and to wipe dry to avoid water marks. ■ Remove food particles after every used. 1) Drawer:Clean the drawer with warm soapy damp sponge or cloth. 2) Drawer Front: Shine with stainless steel cleaner in direction of grain. 3) Gasket: Clean with warm soapy damp sponge (care should be taken when cleaning the gasket because silicon is tough until it is cut, at which time it will tear very easily). 4) Knobs:The on/off temperature knob may be removed to be cleaned (See Fig.07).The moist/crisp knob, however, should never be removed. Be aware that the pull off force will decrease and a loose knob could become a choking hazard for small children. Should the knob come off, use DCS cement (part number 14178) to re-attach the knob. 5) Light: Clean with damp cloth or sponge. 6) Drawer cavity: Same as Drawer above. 7) Element: Care should be taken when cleaning the heating element. Only clean the element when the unit is cool. Use warm soapy water on damp cloth. 8) Stainless Steel tray: Can be removed and cleaned with hot soapy water at sink. 6 USE & CARE INFORMATION REMOVING THE DRAWER Be sure the drawer is cool and no food items or trays are in the drawer. Never attempt to remove the drawer while the unit is on or warm. 1) To remove the drawer,first remove plates, trays, etc.,from the drawer. 2) Pull the drawer open towards you all the way until it reaches the stop position (Fig. 8). 3) Lift up on the handle while pressing the plastic locking tip on both sides and pulling the drawer towards you.The drawer will ride on the side holders and can be lifted up to be fully removed (see Fig. 9 and 10). 4) A strike is located at the center back of the drawer (fig. 11).The catch,which is in the inside of the warming drawer, grabs and holds the strike to keep the door shut tightly. Fig. 10 Fig. 11 7 USE & CARE INFORMATION REPLACING THE DRAWER _A WARNING With the drawer removed, the heating element is exposed (see figure 12). Never turn the unit on while the drawer is removed. Never let children play near or touch the warming drawer while it is not safely installed. Push the slides back int...

Herunterladen

Geben Sie zwei Ziffern: