Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: DCS Dateigröße: 2.77 mb Dateiname: Unterrichtssprache:

3): Note: The cutout of each corner should be 90. for the Access Drawers to fit properly. A 90. B C Vent* CUTOUT DIMENSIONS MODEL A (+0,-1/8) B (+1/8,-0) C ADR48 46” 20” 24-1/2” min. (all models) ADR36 34” 20” ADR30 28” 20” ADR24 22” 20” Vent* Vent* Optimal support locations * Island installation to use minimum of 3 vents providing 10 sq. in. per vent (typical). Fig. 3 2. Place 2 X 4s to provide support for the Access Drawers structure in the locations indicated in the figure below (Fig. 4). 3. Board lengths are provided in the table below (Fig. 5). Fig. 4 CBA8-3/4”8-3/4” To ensure proper drawer operation, be sure your support boards are flat & level. Optimal support locations. SUPPORT BOARD DIMENSIONS MODEL A B C 48” 44” 1-1/2” 3-1/2”* min. 36” 32” 1-1/2” 3-1/2”* min. 30” 26” 1-1/2” 3-1/2”* min. 24” 20” 1-1/2” 3-1/2”* min. *Dependent on application. Fig. 5 4. When installing your support boards, be sure they are level. 5. Check to be certain that the top edges of your boards are level with the bottom edge of the cut-out (Fig. 6). Fig. 6 For proper support & drawer operation, insure that support boards are level front to back & side to side. Support Board (typical) Support Boards (typical) Front View (typical) End View (typical) INSTALLATION REMOVING DRAWERS 1. Once the unit has been inspected, remove the left drawers by pulling them out until their slider latch is visible. Carefully push the latch down on the left side while pulling up on the right side and pull the drawers completely out of the frame (Fig. 7). 2. To remove the LP tank drawer on the right, pull the drawer out and lift the end by the handle to disengage the rollers (Fig. 8). 3. To prevent damage to surfaces, place the drawers on a stable surface on a protective towel or tablecloth. Slider latch Lift Fig. 8 Fig. 7 SLIDE IN FRAME AND MOUNT TO SUPPORT STRUCTURE 1. With the help of an assistant, lift the unit off of the pallet and slide it into the cabinet cutout. Adjust for level and fit. Locate mounting holes on the frame (Fig. 9 and views). Secure the unit using screws suited for the type of cabinet material. NOTE: Depending on the wall thickness and location of mounting holes, an additional board may be required to properly receive the screws. 3/16" TO 1/2" 8" 3/4"3/4" MOUNTING SCREWS (not provided) LOCATIONS VIEW SHOWING HOLES ON LEFT AND RIGHT SIDES AVAILABLE FOR MOUNTING VIEW SHOWING HOLES ON TOP AND BOTTOM OF FRAME AVAILABLE FOR ADDITIONAL SUPPORT Fig. 9 INSTALLATION RE-INSTALLING DRAWERS 1. Re-install the drawers by extending their guides as shown in fig. 10. 2. While holding the drawer parallel to the cabinet, carefully align & engage the ends of the glides. Slide the drawer about an inch so that the glides are supporting the back of the drawer (Fig. 11). Drawer Glide properly Engaged. Fig. 10 Fig. 11 3. While holding the drawer up by the handle er the drawer glide until they click (Fig. 12). 4. As you push the drawers in, you will enc push the drawer all the way in to complete the engagement proc w glide smoothly in & out with light effort (Fig. 13). Drawer Cavity Glide Fig. 12 Fig. 13 INSTALLATION 6. Your LP tank will be installed in the recess provided in the bottom of the right compartment (Fig. 14). Tank Receptacle Fig. 14 7. When connecting the LP tank to the gas line be certain that the gas pipe is routed through the recess provided on the top of the right side (Fig. 15). Do not route the gas pipe through the opening in the back of the Access Drawers. Once gas connections are made, test for gas leaks. 8. On models so equipped, install the two (2) racks provided into the opening by sliding them onto the rollers on the sidewalls of the center cavity (Fig. 16). Drain drawer Rack & Rack Cover Gas Pipe Recess Fig. 15 Fig. 16 CARE & MAINTENANCE All parts of the Professional Access Drawers can be cleaned with hot soapy water, rinsed, dried and buffed to a shine with a soft, heavy cloth. Always try this first, as it is the mildest cleaning procedure. 1. Use the mildest cleaning procedure first. Some brands of cleaners of the same type are harsher than others, read their directions. A scent or a propellant can make a difference in the p...

Herunterladen

Geben Sie zwei Ziffern: