Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Disconnect electricity, remove thermostat and follow the directions for turning the altitude adjustment screw as shown in the label on each thermostat. (continued next page) PREPARATION (continued) Changing the Bin Door Panel You can easily change the color of the front panel on the storage bin door. Two colors are available: black and white. To change the panel: 1. Open the storage bin door. Remove the two screws on the top of the door which hold the handle. 2. Loosen the screws in both of the side trim pieces. 3. Remove the handle and the handle insert. 4. Carefully slide the panel out. You will find the Handle Handle Insert reverse side is black. For units with black panels showing, the reverse side will be white. 5. Choose the color you want to show and carefully slide the panel back into the door. NOTE: Be careful not to scratch the panel as it is inserted. 6. Replace the handle insert and tighten the screws in both side trim pieces. Replace the handle and screws. NOTE: You can make a decorative wood front to match existing cabinets. See the section on Custom Door and Access Panels. Changing the Lower Access Panel WARNING: Do not operate the icemaker with the lower access panel or Lower control panel removed. Electrical shock Access or personal injury could result. Panel 1. Remove the screw from the top of the lower access panel and the two screws in the bottom grille area. Pull forward at the bottom, then down to remove Grill the panel. Area 2. Remove the two screws from the top panel trim and remove the top trim. Screw Screws 3. Carefully slide the panel out. 4. Choose the color you want to show and carefully slide the panel back into the lower access panel. NOTE: Be careful not to scratch the panel as it is inserted. 5. Replace the top trim and screws. Replace the lower access panel assembly and screws. The top of the access panel needs to be secured under the two metal tabs before replacing the screws. NOTE: You can make a decorative wood front to (continued next page) match existing cabinets. See the section on Custom Door and Access Panels. CUSTOM DOOR AND ACCESS PANELS Custom Door and Access Panels—1/4. Thick Door Lower Bin Panel Cut panels to the same size as the production metal panel. 111/4. 1115/16. 1/4. 17. Wood Panel Dimensions Custom Door and Access Panels—3/4. Thick These door and access panels—both raised and flat design—should be constructed in the same manner as typical cabinet doors or drawers. Storage bin door panel: • Cut the panel 17. wide x 111/4. high. • Rout the top and both sides 5/16. wide, 1/2. deep for a total thickness of 1/4. . • Rout the bottom of the panel 1. wide, 1/2. deep for a total thickness of 1/4. . This will allow the door to open without binding against the lower panel. For a custom appearance, consider tapering this 1. rout. Lower access panel: • Cut the panel 17. wide x 1115/16. high. • Rout all four sides 5/16. wide and 1/2. deep for a total thickness of 1/4. . Storage Bin Door Panel 17. 111/4. Rout 1/2. deep, 1. wide across bottom Rout 1/2. deep, 5/16. wide top and sides Rout 1/2. deep, 5/16. wide on all sides Lower Access Panel 1115/16. 17. 3/4. Thick Panels Install Custom Door and Access Panels To install the storage bin door panel: 1. Open the storage bin door. 2. Remove the two screws on top Remove all door of the door which hold the handle. insulation ribs to accept wood 3. Remove the handle. panel thickness 4. Slide the metal panel out. 5. Break off the ribs on the door insulation to allow for the wood thickness. 6. Slide the wood panel into the door frame. 7. Replace the handle and screws. To install the lower access panel: WARNING: Make sure the icemaker is disconnected from the main power supply before removing the lower access panel. Failure to do so could result in electric shock or personal injury. 1. Remove the screw at the top of the lower access panel assembly and the two screws at the bottom that hold the lower access panel assembly to the icemaker. 2. Remove the two screws from the top panel trim. 3. Slide the metal panels and spacers out. 4. Slide the wood panel into the door frame. 5. Replace the top of the panel assembly. NOTE: Make sure the galvanized panel is replaced in back of the panel assembly. Vacation and Moving WARNING: Make sure the icemaker is disconnected from the main power supply before removing the lower access panel. Failure to do so could result in electric shock or personal injury. To shut down the icemaker: 1. Disconnect the electrical power supply to the icemaker and turn the Cycle Control Knob to “OFF.” 2. Remove all ice from the storage bin. 3. Shut off the water supply. 4. Remove the screw from the top of the lower access panel and the two screws from the grille area of the lower access panel, then remove the panel. Pull forward at the bottom, then down. NORMAL THIN THICK OFF ICE Lower Access Panel Grille Area ON CLEAN CYCLE Screw Screws 5. Disconnect the inlet and outlet lines to the water valve. Allow these lines...