Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Wibur Curtis Company Dateigröße: 970.99 kb Dateiname: Unterrichtssprache:

The newly set temperature will now be displayed. To set and exit, press . ENTERING THE PROGRAM MODE #1 For ALL functions you must first enter the programming mode. • Turn OFF the power from the Control Panel by pressing . .. Press and HOLD .. Continue HOLDING and press and RELEASE . until starts blinking; RELEASE. READY TO BREW BREW VOLUME - Factory Preset to Brewer Requirements BREW CYCLE COUNTER For ALL functions you must first enter the programming mode. ..Turn OFF the power from the Control Panel by pressing . .. Press and HOLD and press and RELEASE . .. Continue HOLDING until STOPS blinking; RELEASE. ENTER THE PROGRAM MODE #2 READY TO BREW CHANGE BREW VOLUME - CONCENTRATE ENTER THE PROGRAMMING MODE #1 .. Press and HOLD until hot water starts running from sprayhead; then RELEASE. .. When desired volume is reached, press again to stop flow. • To set and exit, press . CHANGE BREW VOLUME - DILUTION ENTER THE PROGRAMMING MODE #1 .. Press and HOLD until cold water starts flowing from dilution faucet; then RELEASE. • When desired volume is reached, press again to stop flow. • To set and exit, press . TO ACCESS BREW CYCLE COUNTER ENTER THE PROGRAMMING MODE #2: .. will now start a pattern of LONG and SHORT blinks. READY TO BREW This pattern identifies the number of brew cycles. SHORT blinks indicate the brew number from one [1] to nine [9]. LONG blinks separate the 1’s, 10’s, 1,000’s and 10,000’s. CHANGING THE DRIP MODE (DWELL TIME) FEATURE ENTER THE PROGRAM MODE #3 For ALL functions you must first enter the programming mode. • Turn OFF the power from the Control Panel by pressing . .. Press and HOLD and press and RELEASE . .. Continue HOLDING until STOPS blinking and remains on. READY TO BREW ENTER THE PROGRAMMING MODE #3 • The will now blink a pattern of flashes from one READY TO BREW Note: Dwell time setting has an affect on dilution water flow (even though the Drip Mode starts at the end of brewcycle). Drip modes set at 7 minutes or less results in pulsing dilution flow. Drip modes set at 8 minutes or more results in continuous flow of dilution water. to ten. The first blink, if selected = 30 seconds; after that, each blink is one minute. 2 Illustrated Parts List - TCTD-35/35S Curtis Illustrated Parts List - TCTD-35/35S CurtisIllustrated Parts List - TCTD-35/35S CurtisIllustrated Parts List - TCTD-35/35S CurtisIllustrated Parts List - TCTD-35/35S CurtisIllustrated Parts List - TCTD-35/35S Curtis Iced Tea Brewer Iced Tea BrewerIced Tea BrewerIced Tea BrewerIced Tea BrewerIced Tea Brewer ITEM ITEMITEMITEMITEMITEM PART N PART NPART NPART NPART NPART N . ..... DESCRIPTION DESCRIPTIONDESCRIPTIONDESCRIPTIONDESCRIPTIONDESCRIPTION 1WC-3322 BASKET, WIRE 6.4 DIA PTTD/TCTD USE W/WC-3320 2WC-3647 STRAINER BT-10 BREWCONE (EXCEPT PARADISE) 3WC-3320 BREW CONE W/HANDLE 8.8” D W/STRAINER 4WC-3201 HANDLE, BREW CONE BLACK 5WC-3358 BREWCONE ASSY, W/WC-3320, WC-3322 & WC-3647 6WC-750 CONTROL BOARD 120V 60Hz PTTD/TCTD 7WC-5450 COVER, TOP BREWER 8WC-2977-01 FITTING ASS...

Herunterladen

Geben Sie zwei Ziffern: