Stimmen - 5, Durchschnittliche Bewertung: 4.6 ( )

Hersteller: EdgeStar Dateigröße: 238.15 kb Dateiname: Unterrichtssprache:

Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is or how effective your filtration may be. With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you may need to clean the system as often as every 6 months. 1. Turn off the power to the ice maker. Keep the ice maker connected to the water supply and drain pipe. 2. Open the door and scoop out all of the ice cubes. Either discard them or save them in an ice chest or cooler. 3. Remove the 2 screws in the front cover and push forward to remove the front cover. Locate the control box. Notes: Do not use too much force, as the wire leads connected to the power switch can be inadvertently disconnected. Use care in the area of the control box. Do not expose it to moisture. 4. Turn on the power to the ice maker. Pour 8 oz. of nickel-safe ice machine cleaner solution into the water sump. Add 8 oz. of tap water. After about 5 minutes, press down the “Clean” button on the Control Box. The machine will run the Automatic Clean mode. 5. Allow 30 minutes for proper cleaning. After cleaning, shut off the power switch, and unscrew the nut of the water-draining hole on the rear of the unit. Drain off the waste water to some container, and then screw the nut on tightly when the waste water is fully drained off. 6. Repeat steps 4 and 5 (without Ice Maker Cleaning Solution) to rinse the ice making system 3 times. NOTE: The use of the Ice Maker Cleaner Solution in the water sump during the rinse is not needed. 7. Prepare a sanitizing solution made of 1 ounce of household bleach and 2 gallons of hot water (95. to 115. F). Remove the flake covers and slideway from the water sump and wipe the entire bin inside and out, covering the entire surface of the walls. 8. Fill a spray bottle with the sanitizing solution and spray all corners and edges, making sure to cover all surfaces with the solution. Soak the flake covers and slideway in the solution and put back in place after drying. 9. Allow the solution to be in contact for at least 3 minutes, then dry. 10. Repeat step 6 to rinse the ice making system one more time. 11. Reassemble the front cover. 12. Turn on the power again. The machine will return to the regular ice making mode. Important: Discard the first batch of ice. 15 Control Panel (Inside of the front panel) Descriptions of LEDs and buttons: 1. Ice Full (Red) LED: Ice Full indicator light. When this LED is lit, the ice storage bin is full of ice or there is something obstructing the ice-full probe. The unit will stop working. When ice cubes are taken out of the ice storage bin, clearing the ice-full probe, the red LED will keep flashing for 3 minutes. Then the unit will restart and return to the ice making mode. 2. Ice Making (Green) LED: Ice Making indicator light. When this LED is lit, the unit is working in the Ice Making mode controlled by a temperature probe on the evaporator. When the green LED is flashing, the unit is working in the Ice Making mode controlled by a fixed timer. 3. Ice Harvest (Yellow) LED: Ice Harvest indicator light. When this LED is lit, the unit is working in the Ice Harvest mode controlled by a temperature probe on the evaporator. When the yellow LED is flashing, the unit is working in the Ice Harvest mode controlled by a fixed timer. 4. Clean button: When this button is pressed, the unit enters the Cleaning mode. The green and yellow LEDs flash together. To stop the Cleaning mode, just press the button again. 5. Mode button: Mainly for service. When this button is pressed, unit can change from Ice Making mode to Ice Harvest mode, or from Ice Harvest mode to Ice Making mode. You can judge the mode from the status of the green and yellow LEDs. 6. Ice size adjust: Turn the screw clockwise, and the size of the individual ice cubes will be larger in the next cycle; the cycle time will be longer. Turn the knob counter-clockwise, and the ice size will be smaller in the next cycle. Note: It is not recommended that the ice size be adjusted after installation. IMPORTANT: • It is not recommended that the ice size be adjusted unnecessarily since this could damage the machine’s controls. • Do not let water contact the control box. • If the red, green and yellow LEDs are flashing together, the machine is not working. The major fuse of the control box has failed. Call for service. Major Functions 1. Completely automatic operation. 2. When the ice storage bin is full, the machine stops making ice automatically and starts again after the cubes are removed. 3. The different colors of the LED display indicate various operating modes. 4. The fan motor responds to the ambient temperature. If it is cold, the motor will stop working to keep the cooling system in good working condition. 5. Ice cube size is adjustable. 6. A sensitive probe and accurate timer enhance the performance of the ice maker. 7. Built-in compressor protection system. EdgeStar Full Size Ice Maker 16 ...

Herunterladen

Geben Sie zwei Ziffern: