Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Move the agitating motor and the dispensing motor towards you. Then remove the agitator and the auger (ice dispensing). See Fig. 7. Fig. 7 5) Remove the bin control bracket assembly. See Fig. 8. 6) Remove the snap pin, shaft and actuator. 7) Remove the thumbscrews, spout and packing. See Fig 9. Fig. 8 Fig. 9 17 8) Remove the thumbscrews, spout cover, ice dispensing spout, and water dispensing nozzle. See Fig. 10. Fig. 10 9) Immerse the parts removed in steps 4 through 8 in the cleaning and sanitizing solutions for about 15 minutes each. 10) Rinse these parts thoroughly with clean water. 11) Thoroughly wipe the shutter located above the ice dispensing spout. 12) Reassemble the bin control bracket assembly. 13) Place the auger (ice dispensing), agitator, bin control bracket assembly, spout, packing, ice dispensing spout, water dispensing nozzle and spout cover back in position. 14) Clean the storage bin liner, and rinse thoroughly. 15) Plug the icemaker back in. Move the power switch to the "ON" position and replace all parts and panels in their correct positions. 16) Move the control switch to the "ICE" position to start the automatic icemaking process. 18 C. Maintenance IMPORTANT 1. This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 2. To achieve optimum icemaker performance, the following parts need periodic inspection and maintenance: Extruding Head and Upper Bearing Housing and Lower Bearing Evaporator Cylinder Auger Gear Motor Mechanical Seal These parts should be inspected at least once a year or every 10,000 hours of operation. Their service life, however, depends on water quality and environment. More frequent inspection and maintenance are recommended in bad or severe water conditions. Replacement of the following consumable parts is recommended if wear exceeds factory recommendations: Upper Bearing Lower Bearing Mechanical Seal Consult with your local distributor about inspection and maintenance service. To obtain the name and phone number of your local distributor, call Hoshizaki Technical Support at 1-800-233-1940 in the USA. 1. Icemaker and Storage Bin • Hoshizaki recommends cleaning this icemaker at least twice a year. More frequent cleaning, however, may be required in some existing water conditions. • The storage bin is for ice use only. Do not store anything else in the bin. 2. Air Filter A plastic mesh air filter removes dirt and dust from the air and keeps the condenser from getting clogged. As the filter gets clogged, the icemaker's performance will be reduced. Check the filter at least twice a month. When clogged, use warm water and a neutral cleaner to wash the filter. 3. Condenser Check the condenser once a year, and clean if necessary by using a brush or vacuum cleaner. More frequent cleaning may be required depending on the location of the icemaker. 4. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean, soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. 19 D. Preparing the Icemaker for Long Storage WARNING When the icemaker is not used for two or three days under normal conditions, it is sufficient to only move the control switch to the "OFF" position. When storing the icemaker for extended time or in sub-freezing temperatures, turn the water off and drain out all water from the water lines and remove the ice from the bin. The bin should be cleaned and dried. Drain the icemaker water hoses using air or carbon dioxide to prevent damage at sub-freezing temperatures. 1) Close the water supply line shut-off valve. 2) Move the control switch to the "OFF" position. See Fig. 5. 3) Move the dispense mode switch to the "CONTINUOUS" position. See Fig. 5. 4) Activate the dispense sensor to remove the ice from the storage bin. 5) Move the control switch to the "ICE" position. 6) Allow the icemaker to make ice until it stops automatically. 7) Move the control swtich to the "OFF" position. 8) Remove the upper front, top and left side panels. 9) Move the power switch to the "OFF" position. See Fig. 4. 10) Unplug the icemaker from the electrical outlet. 11) Remove the front cover of the storage bin. Pour warm water into the storage bin, to melt any remaining ice. Dry out the storage bin. 12) Disconnect the transport hose. Remove any ice remaining in the hose. 13) Replace the storage bin cover and transport hose in their correct positions. 14) Plug the icemaker back in. 15) Move the power switch to the "ON" position. Replace the panels in their correct positions. 16) Move the control switch to the "DRAIN" position and wait for about 15 minutes for the water system to drain. 17) After the water has drained, move the control switch to the "ICE" position. 18) Open the potable water supply line drain valve and blow the line out using compressed air or carbon dioxide. 19) Close the potable water supply line drain valve. 20) Move the control switch to the "...