Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Note: If there is excess scale on the extruding head, fill the reservoir as described above, then use a clamp on the reservoir hose between the reservoir and evaporator assembly to block flow. Remove the thumbscrews securing the spout, then remove the spout. Pour additional cleaning solution over the extruding head until the evaporator assembly is completely full. Fig. 10 Fig. 11 Slope Scoop Holder Hinge (A) Hinge (B) Hinge Stop Pin Top Panel Spout Extruding Head Reservoir Cover Reservoir Reservoir Hose Overflow Hose Evaporator Assembly Packing Upper Rear Panel Clamp Drain Plug Drain Hose 12) Allow the icemaker to sit for 10 minutes before operation. If you placed a clamp on the reservoir hose in step 11, remove it before operation and replace the spout in its correct position. 13) Plug the unit back in. Move the power switch to the "ON" position. 14) Allow the unit to make ice using the solution. When ice stops coming out, move the power switch to the "OFF" position. Unplug the unit from the electrical outlet. 15) Remove the drain plug to drain any remaining solution. 16) After all of the solution has drained, replace the drain plug in its correct position. 17) Remove the reservoir cover. Using a clean container, pour water into the reservoir until it starts to flow through the overflow hose. Replace the reservoir cover in its correct position. 18) Remove the drain plug to drain the water. Note: If you do not sanitize the icemaker, go to step 11 in "Sanitizing Procedure -Final." 19) After all of the water has drained, replace the drain plug in its correct position. 3. Sanitizing Solution IMPORTANT For safety and maximum effectiveness, use the solution immediately after dilution. Dilute 1.25 fl. oz. (37 ml or 2.5 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach) with 2.5 gallons (9.5 l) of warm water. This is a minimum amount. Make more solution if necessary. Using a chlorine test strip or other method, confirm that you have a concentration of about 200 ppm. 4. Sanitizing Procedure - Initial 1) Remove the reservoir cover. Pour the sanitizing solution into the reservoir until the solution starts to flow through the overflow hose. Replace the reservoir cover in its correct position. 2) Remove the spout and packing. 3) Pour some of the sanitizing solution into a separate, clean container. Use this sanitizing solution and a clean cloth to wipe down the slope, scoop, scoop holder, spout, and packing. 4) Rinse the parts thoroughly with clean water. 5) Replace the packing and spout in their correct positions. 6) Make sure at least 10 minutes have elapsed since you poured the sanitizing solution into the reservoir, then plug the unit back in. Move the power switch to the "ON" position. 7) Allow the unit to make ice using the solution. When ice stops coming out, move the power switch to the "OFF" position. Unplug the unit from the electrical outlet. 40 5. Sanitizing Procedure - Final 1) Remove the drain plug to drain any remaining solution. 2) After all of the solution has drained, replace the drain plug in its correct position. 3) Remove the reservoir cover. Pour the sanitizing solution into the reservoir until the solution starts to flow through the overflow hose. 4) Allow the icemaker to sit for 10 minutes before operation. 5) Plug the unit back in. Move the power switch to the "ON" position. 6) Allow the unit to make ice using the solution. When ice stops coming out, move the power switch to the "OFF" position. Unplug the unit from the electrical outlet. 7) Remove the drain plug to drain any remaining solution. 8) After all of the solution has drained, replace the drain plug in its correct position. 9) Remove the reservoir cover. Using a clean container, pour water into the reservoir until it starts to flow through the overflow hose. Replace the reservoir cover in its correct position. 10) Remove the drain plug to drain the water. 11) After all of the water has drained, replace the drain hose, drain plug, drain clamp and all other removed parts in their original and correct positions. WARNING! CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place. Make sure that none have fallen into the storage bin. 12) Open the water supply line shut-off valve. Check for leaks. 13) Plug the unit back in. Move the power switch to the "ON" position and allow the icemaker to run. 14) After 30 minutes, move the power switch to the "OFF" position. Unplug the unit. 15) Pour warm water into the storage bin to melt all of the ice, then clean the storage bin liner, door liner, and door gasket with a neutral cleaner. Rinse thoroughly after cleaning. 16) Plug the unit back in. Move the power switch to the "ON" position to start the automatic icemaking process. 41 42 B. Maintenance The maintenance schedule below is a guideline. More frequent maintenance may be required depending on water quality, the icemaker's environment, and local sanitation regulations. WARNING 1. Only qualified service t...
Dieses Handbuch ist für folgende Modelle:Andere Küchengeräte - C-100BAF-ADDS (1.59 mb)