Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1. Use pliers to lower leveling legs away from cabinet. With the drawer still removed from the compactor cabinet, place level inside on the floor of the cabinet. Check that the compactor is level from front to back and side to side. Adjust the leveling legs until the compactor is level. 2. Move the compactor close to its final position. 3. Plug into a grounded 3 prong outlet. 4. Carefully move compactor into its final position. Check that compactor is still level. Repeat Step 1 if necessary. 5. Grasp sides of compactor drawer and place bottom of A. Wheel bracket assembly C. Locating stud B. Compactor cabinet D. Self-tapping screw (pivot) 2. Use pliers to lower leveling legs away from compactor cabinet. Adjust legs so there will be a ..." (3 mm) to .." (6.4 mm) space between the top of the compactor and the top of the kitchen cabinet opening. Stand the compactor upright. 3. Remove the plastic plugs from the compactor cabinet top. 4. Move the compactor close to its final position. 5. Plug into a grounded 3 prong outlet. 6. Determine whether you want the compactor cabinet or drawer front flush with the kitchen cabinet face. Using 2 - #8 - 18 x ..." mounting screws (provided in conversion kit), attach the retaining brackets (provided in conversion kit) to the compactor cabinet top as needed. See “Accessories.” ¦ If the compactor cabinet is to be flush with the kitchen cabinet face, place retaining bracket mounting screws through “1.” ¦ If the compactor drawer front is to be flush with the kitchen cabinet face, place retaining bracket mounting screws through “3.” ¦ If the compactor is to be midway between “1” and “3,” place the retaining bracket mounting screws through “2.” drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check to see whether drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe Plate” for further instructions. Undercounter Installation NOTE: Installation hardware is not provided. See “Accessories” for ordering conversion kit. 1. Measure the height of your kitchen cabinet opening. The top of the compactor should be at least .." (3 mm) from the top of the kitchen cabinet opening. B A 123 A. Countertop The rear wheels are preset for a kitchen cabinet opening B. Retaining bracket (provided in conversion kit) height of 34..." (87 cm) (position 1). To adjust for other kitchen cabinet opening heights: ¦ Loosen self-tapping screw just enough to clear stud from hole in position “1.” 7. Carefully lift the front slightly and roll compactor into the kitchen cabinet opening. 8. Using 2 - #8 - 18 x .." mounting screws (provided in conversion kit), fasten the retaining brackets (provided in conversion kit) to the countertop with the mounting screws. Countertop mounting A B C A. Countertop B. Retaining bracket (provided in conversion kit) C. Mounting screw (provided in conversion kit) NOTE: If retaining brackets cannot be attached to the underside of countertop, attach mounting clips (provided in conversion kit) to retaining brackets. Fasten compactor to kitchen cabinet face with mounting screws through the mounting clips. Cabinet-face mounting A C B D A. Mounting clip (provided in conversion kit) B. Kitchen cabinet C. Retaining bracket (provided in conversion kit) D. Mounting screw (provided in conversion kit) 9. Grasp sides of compactor drawer and place bottom of drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check to see whether drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe Plate” for further instructions. Adjusting the Toe Plate If the toe plate rubs the floor covering, the toe plate clearance may be changed as follows: 1. Mark on each side of the toe plate the amount of toe plate that rubs the floor covering. 2. Remove the drawer from the unit. See Step 3 in the “Unpacking” section. 3. Use a ruler and a pencil or chalk to draw a line between the marks on each side of toe plate. 4. Use scissors or utility knife to cut toe plate along line. 5. Replace drawer. If toe plate still rubs floor covering, repeat steps 1-4. Changingthe Decorative Panel There are three options for changing the decorative panel: ¦ Order an acrylic panel ¦ Create a custom panel for use with a trim kit ¦ Create a custom panel for installation without trim To order an acrylic panel or a trim kit, see the “Assistance or Service” section for information or call the toll-free number on the cover. Trim Kit Panel Dimensions Use these dimension drawings to create a custom panel for use with a trim kit. Flat Panel: A ...." (5.6 mm) thick panel is required. This is the same thickness as a standard ..." plywood or paneling. 14..." (37.2 cm) 23....." (60.5 cm) Raised Panel: The outersection of panel must be ...." (5.6 mm) thick to fit into the trim. Use the dimensions shown when designing raised panel sections. 14..." 1..." ...." (5.6 mm) A B ...." (8 mm) both sides ...." (8 mm) 23....." (60.5 cm) (37.2...