Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Ice from the cuber falls into the insulated bin where it is stored until needed. When a user pushes the dispense button, a rotating wheel scoops the ice up to the top front of the bin where there is an outlet to the ice chute. Ice will dispense continually for as long as the push button or lever is depressed or until the bin is empty. Table of Contents Specification/Limitations Page 2-3 Installation Page 4-7 Cleaning Page 8-9 Service Diagnosis Page 10 Parts List Page 11-19 Wiring Diagram Page 20-21 Warranty Information Page 3 Note the warning symbol where it appears in this manual. It is an alert for important safety information on a hazard that might cause serious injury. Keep this manual for future reference. Limitations: Must meet the same limitations as the cuber installed on top of it: 50 F. air minimum 100 F. air maximum Must be installed indoors. Must allow at least 6 inch clearance at the rear and both sides when using an air cooled ice machine. Must allow space for the utility connection at the back. Must have a drain. Options (Field Installed) ( *Required ) *Thermostatic Bin Control Kit (22 Inch Ice Series) Part Number 1051134-01 *Thermostatic Bin Control Kit (30 Inch Ice Series) Part Number 1051020-02 Manual Water Glass Filler Kit Part Number KISWGF Ice Machine Adapters *22 inch cuber Part Number KBT2222 *30 inch cuber Part Number KBT3030 *22 inch machine on a 30 inch dispenser Part Number KBT2230 Leg Kit Part Number KIOD4 Dispenser Specifications Storage Basic Min. Circuit Model Number Capacity(lbs-kgs) Electrical Actuation Ampacity Max. Fuse Size IOD16022 160/70 115/60/1 Lever 2 15 IOD16022 160/70 115/60/1 Button 2 15 IOD22030 220/100 115/60/1 Lever 2 15 IOD22030 220/100 115/60/1 Button 2 15 Dimensions ( Inches) Model Number Width Depth Height IOD16022 22 inches 32 inches 34 inches IOD22030 30 inches 32 inches 34 inches Note: Counter top legs are included with the dispenser. Ice-O-Matic ice machines are not designed for outdoor installations. Machine requires voltage indicated on rating nameplate. Failures caused by improper voltage are not considered factory defects. Extended periods of operation at temperatures exceeding limitations constitutes misuse under the terms of the Ice-O-Matic Manufacture’s Limited Warranty, resulting in a loss of warranty coverage. Specifications and design are subject to change without notice. The IOD16022 and IOD22030 carry a 2 year Parts warranty and a 1 year Labor Warranty. Equipment Description The IOD16022 and IOD22030 are counter top mounted ice only dispensers. These units are designed to dispense cube ice only and have ice storage capacities of 160 lb. and 220 lb. respectively. Site Preparation The site chosen for the dispenser must be capable of supporting the dispenser with a full bin of ice plus all other loads being placed on the surface supporting the dispenser. If an ice machine is being placed on the dispenser, the weight of the ice machine must be included in the calculations to determine the support structure needed for the dispenser. Allow sufficient clearance above the unit for removal of the cover and for pouring ice into the bin. A 115 volt, 15 amp electric outlet needs to be located within 6 feet of the unit. The outlet must be properly grounded and fused. No other electrical appliance should be on the circuit. ALL ELECTRICAL WIRING MUST CONFORM TO NATIONAL AND LOCAL CODES Do not place the dispenser next to heat sources such as ovens, heat ducts or in the warm air discharge from adjacent equipment. The unit must be located near a building drain. Drain lines must be properly vented and pitched to ensure free flowing of wastewater to the drain. These dispensers are designed to dispense cubed ice only. Do not use flaked, crushed or compressed ice forms. If an Ice-O-Matic ice machine is to be placed on top of the dispenser, an adapter will be required. Ice Machine Adapter 22 inch cuber Part Number KBT2222 Ice Machine Adapter 22 inch cuber on 30 wide dispenser Part Number KBT2230 Ice Machine Adapter 30 inch cuber Part Number KBT3030 Dispenser Preparation Remove the shipping carton and discard. Remove the merchandiser by lifting up on the merchandiser and pulling it forward. Remove the drain pan from the skid, and all hardware from the bin. Remove the splash panel by removing the two phillips head screws near the bottom corners of the panel. Remove the 4 brackets holding the dispenser to the skid. (Optional) Screw 4 legs into the well nuts in the bottom of the dispenser. In order to comply with NSF requirments, this unit must be either elevated above the counter top sufficiently to provide space for cleaning under the unit or the unit must be sealed to the counter top. Elevating the unit may be accomplished by using legs. (IOM Part Number KIOD4) Drain Line Installation (Dispenser) Connect a .” ID flexible drain hose to the drain nipple located under the ice storage bin. Clamp the hose in place and insulate the hose to prevent condensation. Connect a...
Dieses Handbuch ist für folgende Modelle:Andere Küchengeräte - Counter Top Dispenser IOD22030 (1.84 mb)