Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Make sure you have all YOU MAY NEED: necessary disposer parts before install- Phillips Screwdriver, Drain Auger, 3/8" Electrical Clamp ing the disposer (see part identification Connector, Wire Nuts (2), Second 1 1/2" Drain Trap, diagram below). Hammer, Hacksaw, Water Hose Clamp, Pipe Wrench, Copper Ground Wire, Dishwasher Drain Connection Kit, Air Gap, Electrical On/Off Switch, Drain Tube Extension (_)1& 1 d #1 00 Otc N OR K #2 Mounting Assembly Disposer Discharge Assembly #1 A Stopper H Mounting Gasket/Splash Baffle M Nut B Sink Flange I Lower Mounting Ring N. Beveled DLscharge Tube C F_ber Gasket J D_shwasher Inlet #1 (1-1/2" Dlam ) D. Backup Rmg K D_scharge Outlet O. Beveled Washer E. Mounting Ring L' Wrenchette P. Flanged Gasket F Screws (3) OR G Snap Ring --Discharge Assembly #2 M. Bolt N. Discharge Tube (1-1/2" Diarn ) #2 O Flange P Gasket SAFETY SYMBOLS Danger indicates an I'_kWARNING I Warning indicates [',_gCAUTIONI Caution indicates a imminently hazardous situation which, a potentrally hazardous s_tuation potentially hazardous situation which, if not avoided, senous injury wdl result m death or which, if not avoided, could result death or serious injury m if not avoided, may result m minor moderate mjury or 72785 CHECK INSTALLATION DIMENSIONS 1odel A BC bE A. Disposer Height 010/6012 113/8" 6" 4" 65/16" 5" bowl to centerline of discharge ] B 01116013 12 5/8" 6" 4" 6 5/16" 5" B. Distance from bottom of sink outlet. (Add 1/2" when stainless steel sink is used.) A, 0552 12 5/8" 6" 4" 7 1/4" 5" C: Distance from centerline of the discharge outlet to end 5/8'--6,' 4,' 71/4,' 5" L of discharge tube. _3/4" 611/16" _ 53/4'_ 4'=._81/2'.=_=___' D: D_sposer Width D ---'----- E: Distance from disposer vertical 3/4" 6 11/16" 4" 8 1/2" 5 3/4" centerline to centerline of 0559* _1157/8" 9 7/16" 4" 7 1/2" 5 3/4" P-trap connection. --" 6" 4"71/4" 5" F: Centerline of disposer discharge to centerline at waste pipe entering wall. (Dimension "F" must be greater than 1/4" to prevent standing water in disposer.) 6" 4" 7 1/4" 5" If replacing an existing disposer, skip ahead to Instruction 6. ] _'" Indicates Batch Feed Model If this is a first time installation, continue with Instruction 2. / DISCONNECT SINK DRAIN 1. Loosen nut (A) at top of "P-trap" with pipe wrench (see Figure 2-1). 2. Loosen nut (B) at top of extension pipe. Remove extension pipe. J 3. Loosen nut (C) at base of sink flange. (If nut is corroded or too tight, apply penetrating lubricant 4. Push s_nk flange up through sink hole and remove it (see Figure 2-2). 5. Clean sink flange area of any putty or other debris. "- r " /_ DISASSEMBLE NEW DISPOSER MOUNTING ASSEMBLY 2-1 2-2 1. Insert wrenchette (or screwdriver) into one mounting lug and hold lower mounting ring securely with one hand (see Figure 3-1). With your other hand, turn mounting assembly counterclockwise to remove mounting assembly from lower mounting ring 2. Turn mounting assembly over (see Figure 3-2) and loosen three mounting / !i screws (A) until you can access snap ring (B). 3 Use screwdriver to pry snap ring off of sink flange. Mounting assembly will now come apart. INSTALL FLANGE IN SINK HOLE 3-1 3-2 1. Roll 1/4 pound (4 oz.) of non-hardening plumber's putty to make 3/4" thick rope to seal around sink flange. 2. Apply putty evenly around sink hole (see Figure 4-1). 3. Press sink flange slowly but firmly into sink drain hole to seat evenly on putty (see Figure 4-2). Use screwdriver or putty knife to scrape all putty from edge of sink hole. _k CAUTION Do not use plumber's putty on any other disposer connection -it 4-1 4-2 may harm disposer and cause property damage. ATTACH UPPER MOUNTING ASSEMBLYTO SINK FLANGE Sink Flange You may wish to place a we=ghted object in the sink to hold the sink flange in place. (Place a towel under object in sink to prevent scratching ) Reference F=gure 5-1 for part identification. Fiber Gasket / 1 Working from under sink, slip fiber gasket and 4 Tighten three mounting screws up to sink metal backup ring over sink flange. until mounting assembly is seated tightly Backup R=ng __ _._'_). 2 Holding fiber gasket and backup ring in place, and evenly against sink. shp mounhng nng over s_nkflange so it seats * Placing a thick, wide rubber band around against backup nng the sink flange (above the snap ring MountEng RLng __ X_-@ 3 W_th fiber gasket, backup nng, and mounting groove) may help hold parts Jnplace _,,hde ring hght to S,F.'.__ottom, shde snap r',ng cnto tnstalhng snap ring. (Remember to rer'nove s_nk flange until _tpops {nto groove on flange'. rubber band after snap ring is installed.) ' Snap Ring O If you are replacing an existing disposer, go to Instruction 6 If this is a first time _nstallahon, 1 skip ahead Io Instruction 7 J 5-1 REMOVE EXISTING DISPOSER 1. Turn off electrical power at fuse box or circuit breaker. Electric Shock o Turn off electrical power at fuse ,, Disposer must be grounded. box or circuit breaker before Improper connection can removing elect...