1.00 - 9 - SRP-350II 1-2-3 USB Interface USB IFG-U TYPE Drawer kick-out connector Power supply connector USB connector Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Power : DC5[V] / 500[mA] 2 D-White Differential Data Line 3 D+ Green Differential Data Line 4 GND Black Signal Ground 1-3 Connecting the Drawer . WARNING Use a drawer that matches the printer specification. Using an improper drawer may damage the drawer as well as the printer. .

* Utility water pipes • Plastic water pipes should not be used for grounding. (Those approved by a Waterworks Department may be used.) ¦ Before connecting or disconnecting the grounding lead to or from the printer, always unplug it from supply outlet. — 4 — PRECAUTIONS IN HANDLING THE PRINTER WARNING Please observe the following precautions for power source and power cord: ¦ Do not plug or unplug the power cord with a wet hand. ¦ Use the printer only at the specified supply voltage and frequency

..............................................................................................................................................................................P ......................................................................................................................................................................Q ............................................................................................................................................................

This data remains stored even after the printer power is off. For the registration method, refer to Command Reference Manual in separate document. To acquire the Command Reference Manual, contact your Citizen Systems dealer. . Memory switch Setting of various kinds of functions can be stored in nonvolatile memory. The functions are valid even if the printer power is turned off. — 14 — 3. PREPARATION 3.1 Connecting the AC Power Cord 1. Turn off the printer power switch. 2. For AC power type (with

*2: The ERROR LED may blink even in the execution of macro function. 4.7 When the Paper Cover Cannot Be Opened If the cutter blade remains protruded due to paper jam or for any abnormality, opening the paper cover may be disabled. In this case, do not open the paper cover forcibly. Insert a Phillips screwdriver (size #1) into the cutter lock releasing feed hole and turn it in the direction of arrow (clockwise). When you find that both ends of the blade reached the lowest position, stop turning t

LVD: EN60950 EMC : EN55022 Class B EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. CITIZEN is a registered trade mark of Citizen Holdings Co., Japan CITIZEN es una marca registrada de Citizen Holdings Co., Japon Company names and product names in this manual are trademarks or registered trademarks of relevant companies. Copyright c 2008 by CITIZEN SYSTEMS JAPAN CO., LTD. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not

1.00 - 12 - SRP-F310/312 1-5-5 Be sure to note the correct direction that the paper comes off the roll. O x 1-5-6 Pull out a small amount of paper, as shown. Then close the cover. * NOTE When closing the cover, press the center of printer cover firmly to prevent paper miss-loading. 1-5-7 Tear off the paper as shown. Rev. 1.00 - 13 - SRP-F310/312 1-6 Adjustments and Settings The SRP-F310 is set up at the factory to be appropriate for almost all users. It does, however, offer some set

1.00 SRP-F310/312 ■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. âs WARNING • i Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. • This can provoke over-heating and a fire. • If the plug is wet or dirty, dry or wipe it before usage. • If the plug does not fit perfectly with the outlet, do not plug in. • Be sure to u

2 W, Printing: Approx. 18 W (Approx. 26 W max.) AC adapter Rated input: AC 100 to 240 V, 50/60 Hz Rated output: DC 8.5 V, 2.5 A Weight Approx. 430 g Outside dimensions 106 (W) x 170 (D) x 116.5 (H) mm Operating temperature and humidity 5 to 40°C, 10 to 85% RH (No condensation) Storage temperature and humidity -20 to 60°C, 10 to 90% RH (No condensation) Reliability Print head life: Pulse resistance: 1 x 108 pulses (Printing rate 12.5%) Wear resistance: 50 km (At normal temperatu

printing width: 4.1 in (104 mm) • Max. paper width: 4.65 in (118 mm) • Max. printing length: 32 in (812 mm) Printing speed • 2–4 inches/second in one-inch units Print mode • Batch mode: Normal printing (single or multi sheets) • Peeling mode: Label peeling off the liner after printing • Cut mode: Cutting and printing by the specified number of sheets (label feeding back enabled) • Tear-off mode: Paper feeding back to the printing start position after cutting Bar code generator One-dimensional ba