1. Important Information
R Unplug this unit from power outlets and refer servicing to an authorised
1.1 For your safety
service centre when any of the following conditions occur:
–
If the power cord is damaged or frayed.
1. . Important Information
To prevent severe injury and loss of life/property, read this section
carefully before using the unit to ensure proper and safe operation of
–
If the unit has been exposed to rain or water, or liquid has been
your unit.
spilled into the unit. Do not use a microwave oven to speed up the
drying process of any parts of the unit to avoid permanent damage.
–
If the unit does not work normally by following the operating
1.1.1 WARNING
instructions. Adjust only controls covered by the operating
instructions. Improper adjustment may require extensive work by
Power and ground connection
an authorised service centre.
R Unplug this unit from power outlets if it emits smoke, an abnormal smell
–
If the unit has been dropped or physically damaged.
or makes unusual noise. These conditions can cause fire or electric
shock. Confirm that smoke has stopped and contact an authorised
–
If the unit exhibits a distinct change in performance.
service centre.
USB cable
R Use only the power source marked on the unit. If you are not sure of
R To assure continued emission limit compliance, use only shielded USB
the type of power supplied to your home, consult your retailer/dealer
cable (Example: Hi-Speed USB 2.0 certified cable).
or local power company.
R For safety purposes this unit is equipped with a grounded plug. If you
1.1.2 CAUTION
do not have this type of outlet, please have one installed. Do not ignore
this safety feature by tampering with the plug.
Installation and relocation
R Do not place objects on the power cord. Install the unit where no one
R After moving the unit from cold areas to warmer areas, wait
can step or trip on the cord.
approximately 30 minutes before turning on the power switch to allow
R Do not overload power outlets and extension cords. This can result in
the unit to adjust to the ambient temperature. If the power switch is
the risk of fire or electric shock.
turned on too soon after a sudden climate change, condensation may
R Completely insert the AC adaptor/power plug into the power outlet.
form inside the unit, causing malfunction.
Failure to do so may cause electric shock and/or excessive heat
R Never turn the unit upside down or sideways when moving it.
resulting in a fire.
R Never install telephone wiring during a lightning storm (KX-MB1520
R Regularly remove any dust, etc. from the AC adaptor/power plug by
only).
pulling it from the power outlet, then wiping with a dry cloth. Accumulated
R Never install telephone jacks in wet locations unless the jack is
dust may cause an insulation defect from moisture, etc. resulting in a
specifically designed for wet locations (KX-MB1520 only).
fire.
R Never touch uninsulated telephone wires or terminals unless the
R Never touch the plug with wet hands. There is a danger of electric shock.
telephone line has been disconnected at the network interface
Installation
(KX-MB1520 only).
R Place the unit securely on a stable, level surface. Serious damage and/
R Use caution when installing or modifying telephone lines (KX-MB1520
or injury may result if the unit falls.
only).
R To prevent the risk of fire or electrical shock, do not expose this product
R Do not position the unit in a location where it is unstable or subject to
to rain or any type of moisture.
vibrations.
R Use this unit in a well ventilated area. Particularly, if you will be using
Laser radiation
the unit for extended periods of time or will be printing in large volumes,
be sure to ventilate the room sufficiently.
CLASS 1 LASER PRODUCT
Operating safeguards
R The printer of this unit utilises a laser. Use of controls or adjustments
R Turn the power OFF before cleaning. Do not use liquid or aerosol
or performance of procedures other than those specified herein may
cleaners.
result in hazardous radiation exposure.
R Do not cover slots and openings on the unit. They are provided for
See the operating instructions for the Laser diodes properties.
ventilation and protection against overheating. Never place the unit
near radiators, or in a place where proper ventilation is not provided.
LED light
R Never push any objects through slots in this unit. This may result in the
risk of fire or electric shock. Never spill any liquid on the unit.
CLASS 1 LED PRODUCT
R To reduce the risk of electric shock, do not disassemble this unit. Take
R When using the unit, do not look directly at the CIS’s LED light. Direct
the unit to an authorised service centre when service is required.
eye exposure can cause eye damage.
Opening or removing covers may expose you to dangerous voltage or
other risks. Incorrect reassembly can cause electric shock when the
See the operating instructions where the CIS LED specifications are
unit is subsequently used.
listed.
R Follow all warnings and instructions marked on this unit.
Fuser unit
R Do not spill liquids (detergents, cleansers, etc.) onto the telephone line
cord plug, or allow it to become wet at all. This may cause a fire. If the
R During or immediately after printing, the fuser unit gets hot. This is
telephone line cord plug becomes wet, immediately pull it from the
normal. Do not touch the fuser unit.
telephone wall jack, and do not use (KX-MB1520 only).
Detailed operating instructions are on the CD-ROM.
3

---

...

Dieses Handbuch ist für folgende Modelle:
Drucker - KXMB1520SL (457.17 kb)
Drucker - KXMB1520NL (457.17 kb)
Drucker - KXMB1520JT (457.17 kb)
Drucker - KXMB1520G (457.17 kb)