Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Fujitsu Dateigröße: 34.51 kb Dateiname: ftp-622dcl_dsl001_011_101.pdf Unterrichtssprache:

Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET — Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET — Connected to logic GND 5 PRDT1 I Data 1 6 PRDT1-RET — Connected to logic GND 7 PRDT2 I Data 2 8 PRDT2-RET — Connected to logic GND 9 PRDT3 I Data 3 10 PRDT3-RET — Connected to logic GND 11 PRDT4 I Data 4 12 PRDT4-RET — Connected to logic GND 13 PRDT5 I Data 5 14 PRDT5-RET — Connected to logic GND 15 PRDT6 I Data 6 16 PRDT6-RET — Connected to logic GND 17 PRDT7 I Data 7 18 PRDT7-RET — Connected to logic GND 19 ACKNLG O Data input acknowledge 20 ACKNLG-RET — Connected to logic GND 21 BUSY O Busy 22 BUSY-RET — Connected to logic GND 23 RINF2 O Printer status 24 INPRM-RET — Connected to logic GND 25 SLCTIN I Printer select 26 INPRM I Reset 27 RINF1 O Printer status 28 RINF3 O Printer status 29 ATF I Paper feed request 30 GND — Logic GND Notes: • Symbol “——” means a negative logic signal. • “–RET” signal is a return signal of the twisted pair cable. • “I” or “O” means a signal direction from the interface board side. (3) Connector pin number (4) Data input signal timing FCN-605Q030-G/S (Fujitsu Components) or equivalent No.30 No.2 No.1 PRDT0~7PRSTBBUSYACKNLGt1t3t2t4t5:t1.0.5msec:t2.0.5msec:t3.0.5msecPRSTBtoBUSY=“H” ACKNLGpulse:t4.0.5msec:t5=5.0msec.. DatasettimePRSTBpulseDataholdtime FTP-622DCL/DSL Product Part Number Function Parallel Interface Board FTP-622DCL001 Standard (without cutter) FTP-622DCL011 With cutter control FTP-622DSL001 Standard (without cutter) Serial Interface Board FTP-622DSL011 With cutter controller FTP-622DSL012 With cutter controller + FLASH ROM FTP-622DSL112 With Cutter + KANJI+FLASH ROM n SPECIFICATION Item Specification Data receive speed 19200, 9600, 4800, 1200 bps (set by dip switch) Synchronous method Asynchronous, full duplex Hand shake DTR/DSR signal or XON/XOFF Input output level RS232C Signal level Space (logic = 0) +3 V ~ +12 V Mark (logic = 0) –3 V ~ –12 V 2. SERIAL INTERFACE (RS232C) (1) Connector (CN2) Part number : B6B-XH-A (J.S.T) Mating connector part number : XHP-6 (J.S.T) or equivalent (2) Pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 FG — Frame GND 2 RD I Receive data 3 TD O Transmission Data 4 DTR O Data terminal ready 5 GND — Signal GND 6 DSR I Data set ready Notes: “I” or “O” means a signal direction from the interface board side. (3) Pin number B6B-XH-A (J.S.T) 6 1 CN2 CN1 FTP-622DCL/DSL n CONNECTOR PIN ASSIGNMENT 1. Connector for power supply (CN10) Part number : B6P-VH (J.S.T) Mating connector part number : VHR-6N (J.S.T) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 VCC — Power supply for logic (+5 V) 2 GND — GND (5 V, 24 V common) 3 GND — GND (5 V, 24 V common) 4 GND — GND (5 V, 24 V common) 5 VDD — Power for head/motor (+24 V) 6 V DD — Power for head/motor (+24 V) 2. Connector for thermal head drive (CN8) Part number : B16B-PH-K-S (J.S.T) Mating connector part number : PHR-16 (J.S.T) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 VDH O Power for head (+24 V) 2 VDH O Power for head (+24 V) 3 GND (VDH) — Head GND 4 GND (VDH) — Head GND 5 STB1 O Print enable signal 1 6 STB2 O Print enable signal 2 7 STB3 O Print enable signal 3 8 TMP I Temperature detection signal 9 STB4 O Print enable signal 4 10 LAT O Print data latch signal 11 STB5 O Print enable signal 5 12 5 VH O Power for logic (+5 V) 13 HCLK O Data transmission clock 14 HD O Print data output signal 15 GND (VDH) — Head GND 16 VDH O Power for head (+24 V) Notes: • Symbol “——” means a negative logic signal. • “I” or “O” means a signal direction from the interface board side. 3. Connector for Sensor (CN3) Part number : B5B-PH-K-S (J.S.T) No. Signal I/O Contents No. Signal I/O Contents 1 +5 V — Power for logic (+5 V) 2 PES I Paper end detect signal 3 GND (5 V) — Logic GND 4 +5 V — Power for logic (+5 V) 5 HUP I Head-up detect signal FTP-622DCL/DSL 7. Connector for control signal input/ output (CN1) Part number : FCN-605Q030-G/S (Fujitsu Components) Mating connector : FCN-607B030-G/D (Fujitsu Components) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 NC — No connection 2 NC — No connection 3 NC — No connection 4 NC — No connection 5 NC — No connection 6 NC — No connection 7 NC — No connection 8 NC — No connection 9 NC — No connection 10 NC — No connection 11 NC — No connection 12 NC — No connection 13 NC — No connection 14 NC — No connection 15 NC — No connection 16 NC — No connection 17 NC — No connection 18 NC — No connection 19 NC — No connection 20 NC — No connection 21 NC — No connection 22 NC — No connection 23 NC — No connection 24 NC — No connection 25 SLCTIN I Select signal 26 INPRM I Reset signal 27 NC — No connection 28 NC — No connection 29 ATF I Paper feed request 30 GND — GND *Do not connect outside signal to NC. FTP-622DCL/DSL 4. Connector for paper near end d...

Herunterladen

Geben Sie zwei Ziffern: