Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Set the paper guides to the copy paper width. Insert the copy paper (print face down) all the way into the bypass tray. . Paper must be fed narrow side into the feed slot. . Transparency film, labels, and other special purpose papers must be fed individually. . When copying onto transparency film, remove each copy promptly. Do not let copies stack up. . When loading an envelope, make sure that it is straight and flat. 18 BYPASS FEED Print face Press the tray select ( ) key to select the bypass tray. Set the number of copies if using standard copy paper. Press the print ( ) key. 2 Making copies 19 COPIER TROUBLE? This chapter describes misfeed removal and troubleshooting. MISFEED REMOVAL When the misfeed ( ) indicator blinks or blinks in the display, the copier will stop because of a misfeed. If a misfeed occurs when using the RSPF, a number may appear in the display after a minus sign. This indicates the number of the originals that must be returned to the document feeder tray after a misfeed. Return the required number of originals. Then this number will disappear when copying is resumed or the clear ( ) key is pressed. When the RSPF misfeeds an original sheet, the copier will stop and the RSPF misfeed ( ) indicator will blink, while the misfeed ( ) indicator will remain off. For a misfeed of originals in the RSPF, see “D Misfeed in the RSPF” on page 30. Ensure that the bypass tray is open and then open the side cover while pressing the side cover open button. 5 Copier trouble? Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If blinks in the display, proceed to “A Misfeed in the paper feed area”. (p. 28) in the transport area”. (p. 29) If paper is misfed here, proceed to “A Misfeed in the paper feed area”. (p. 28) If paper is misfed here, proceed to “B Misfeed in the fusing area”. (p. 28) If the misfed paper is seen from this side, proceed to “C Misfeed 27 MISFEED REMOVAL A Misfeed in the paper feed area Gently remove the misfed paper from the paper feed area as shown in the illustration. When blinks in the display and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to “B Misfeed in the fusing area”. The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury. . Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. . If the paper has been fed through the bypass tray, do not remove the misfed paper through the bypass tray. Toner on the paper may stain the paper transport area, resulting in smudges on copies. 5 Close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the ready ( ) indicator will light up. B Misfeed in the fusing area Lower the fusing unit release lever by rotating it all the way as shown in the illustration. Copier trouble? While you are lowering the fusing unit release lever, it will not move smoothly at a location on the way. However, be sure to lower the lever by rotating it all the way to the location where it will not rotate as shown in the right illustration. Fusing unit release lever Gently remove the misfed paper from under the fusing unit as shown in the illustration. If the paper cannot be removed, proceed to “C Misfeed in the transport area”. The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury. 28 29 5 Copier trouble? MISFEED REMOVAL Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. Do not remove the misfed paper from above the fusing unit. Unfixed toner on the paper may stain the paper transport area, resulting in smudges on copies. Raise the fusing unit release lever and then close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the ready ( ) indicator will light up. C Misfeed in the transport area Lower the fusing unit release lever by rotating it all the way as shown in the illustration. Fusing unit release lever Push gently on both sides of the front cover to open the cover. While you are lowering the fusing unit release lever, it will not move smoothly at a location on the way. However, be sure to lower the lever by rotating it all the way to the location where it will not rotate as shown in the right illustration. MISFEED REMOVAL Rotate the feeding roller in the direction of the arrow and gently remove the misfed paper from the exit area. Feeding roller Raise the fusing unit release lever, close the front cover and then close the side cover by pressing the round projections near the side cover open button.The misfeed ( ) indicator will go ou...