Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
^ Make sure that the paper is properly loaded. 15 Pieces of paper inside machine. ^ Remove all pieces of misfed paper. 80 Too much paper is loaded in the tray. ^ If the stack of paper is higher than the indicator line on the tray, remove some of the paper and reload so that the stack does not exceed the line. 15 Some sheets of paper stick together. ^ Fan the paper well before loading it. 21 The guides on the bypass tray do not match the width of the paper. ^ Adjust the guides to match the width of the paper. 18 The bypass tray extension is not pulled out. ^ When loading a large size of paper, pull out the extension. 18 White or black lines appear on copies. The scanner glass for the SPF/RSPF is dirty. ^ Clean the long, narrow scanning glass. 88 The transfer charger is dirty. ^ Clean the transfer charger. 89 73 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution Page Paper size for a paper tray cannot be set. Copying or printing is performed. ^ Set the paper size after copying or printing is complete. - The machine has stopped temporarily due to running out of paper or a misfeed. ^ Load paper or remove the misfeed, and then set the paper size. 19, 79 A copy job stops before it is finished. "MEMORY FULL, PRESS START TO RESUME." appears in the display. ^ The memory became full during sort copy. Copy only the originals that have been scanned to that point, or cancel the job and clear the data from memory. 30 The tray is out of paper. ^ Load paper. 15 The power save indicator is lit. Other indicators are lit. ^ If other indicators are lit, the machine is in preheat mode. Press any key on the operation panel to resume normal operation. 13 Only the power save indicator is lit. ^ If only the power save indicator is lit, the machine is in auto power shut-off mode. Press the [START] key (@) to resume normal operation. 13 Error indicator ( ^ ) is lit or blinking. See "DISPLAY MESSAGES" to check the meaning of the error indicator and error message in the display, and take appropriate action. 69 Lighting fixture flickers. The same power outlet is used for the lighting fixture and the machine. ^ Connect the machine to a power outlet which is not used for other electric appliances. - 74 PROBLEMS DURING SETUP THE SOFTWARE If the software does not install correctly, check the following items on your computer. To remove the software, see "Removing the software" (p.78). MFP driver cannot be installed (Windows 2000/XP) If the MFP driver cannot be installed in Windows 2000/XP, follow these steps to check your computer's settings. Click the "start" button and then click "Control Panel". In Windows 2000, click the "Start" button, select "Settings", and then click "Control Panel". Click "Performance and Maintenance", and then click "System". In Windows 2000, double-click the "System" icon. Click the "Hardware" tab and then click the "Driver Signing" button. Check "What action do you want Windows to take?" ("File signature verification" in Windows 2000). If "Block" has been selected, it will not be possible to install the MFP driver. Select "Warn" and then install the MFP driver as explained in "INSTALLING THE SOFTWARE". 75 TROUBLESHOOTING AND MAINTENANCE Plug and play screen does not appear (USB only) If the Plug and Play screen does not appear after you connect the machine to your computer with a USB cable and turn on the machine, follow the steps below to verify that the USB port is available. B Click the "start" button, click "Control Panel", and then click "Performance and Maintenance". In Windows 98/Me/2000, click the "Start" button, select "Settings", and then click "Control Panel". 2 Click "System", click the "Hardware" tab, and click the "Device Manager" button. "Universal Serial Bus controllers" will appear in the list of devices. In Windows 98/Me, double-click the "System" icon and click the "Device Manager" tab. In Windows 2000, double-click the "System" icon, click the "Hardware" tab, and click the "Device Manager" button. If the "System" icon does not appear in Windows Me, click "view all Control Panel options". Click the + icon beside "Universal Serial Bus controllers". - Universal Serial Bus controllers Standard OpenHCD USB Host Controller USB Root Hub Two items should appear: your controller chipset type and Root Hub. If these items appear, you can use the USB port. If the "Universal Serial Bus controllers" shows a yellow exclamation point or does not appear, you must check your computer manual for USB troubleshooting or contact your computer manufacturer. Once you have verified that the USB port is enabled, install the software as explained in "INSTALLING THE SOFTWARE". 76 TROUBLESHOOTING AND MAINTENANCE The MFP driver cannot be correctly installed by Plug and Play (Windows 2000/XP) (USB only) In Windows 2000/XP, if the MFP driver cannot be correctly installed by Plug and Play (for example, Plug and Play takes place without copying the required fil...