Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Misfeed in the transport area”. If paper is misfed here, proceed to “B. Misfeed in the fusing area”. If paper is misfed here, proceed to “A. Misfeed in the paper feed area”. Roller rotating knob 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. A. Misfeed in the paper feed area 1 Push gently the right side of the front cover to open the cover. 2 Carefully remove the misfed paper. Turn the roller rotating knob in the direction of the arrow to assist in removing it. The fusing unit is hot. Take care in removing paper. Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. 3 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. l The misfeed ( ) indicator will go out. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. B. Misfeed in the fusing area 1 Push gently the right side of the front cover to open the cover. 39 STATUS INDICATORS MISFEED REMOVAL Misfeed removal Roller rotating knob Fusing unit release lever 2 Turn the roller rotating knob in the direction of the arrow. 3 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. Return the release levers to their operating positions. The fusing unit is hot. Take care in removing paper. l Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. l Be careful about unfixed toner on the misfed paper not to soil your hands or clothes. 4 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. l The misfeed ( ) indicator will go out. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. C. Misfeed in the transport area 1 Open the paper guide by pressing down the projection on either side of the guide and remove the misfed paper. The fusing unit is hot. Take care in removing paper. 2 If the misfed paper cannot be removed by the previous step but is visible in the paper output area, remove the paper by pulling it into the paper output area. MISFEED REMOVAL STATUS INDICATORS Misfeed removal 3 3 Close the side cover by pressing the handle on the cover. l The misfeed ( ) indicator will go out. Misfeed in the upper paper tray Before opening the paper tray, be sure to open the bypass tray, lift slightly on the side cover and slide the cover out until it stops, and then perform steps 1 to 3 described in the “A. Misfeed in the paper feed area” section. 1 1 Gently lift and pull out the paper tray and remove the misfed paper. 2 2 Close the paper tray. 3 3 Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover. l The misfeed ( ) indicator will go out. Misfeed in the lower paper tray 1 1 Grasp the handle of the lower side cover and gently open the cover. 40 MISFEED REMOVAL 2 2 Remove the misfed paper. l Be careful not to tear the misfed paper during removal. 3 3 If the misfed paper is not seen in step 2, gently lift and pull out the lower paper tray and remove the misfed paper. l Be careful not to tear the misfed paper during removal. 4 4 Close the paper tray. 5 5 Close the lower side cover. l The misfeed ( ) indicator will go out. STATUS INDICATORS Misfeed removal 41 USER PROGRAMS USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. List of user programs This copier has the following user programs. Program No. Program name Description 1 Auto clear time Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made. 2 Preheat mode Sets the time that elapses before the copier enters the preheat mode after any operation is made. See page 44. 3 Auto power shut-off timer Sets the time that elapses before the copier enters the auto power shut-off mode after any operation is made. See page 44. 4 Stream feeding mode Enables or disables the stream feeding mode. For description of the stream feeding mode, see page 17. 5 Auto power shut-off setting Enables or disables the auto power shut-off mode. See page 44. 8 Auto paper select mode Enables or disables the auto paper selection. See page 16. 9 Auto tray switching Enables or disables the automatic tray switching which occurs when paper in a tray runs out. (This switching cannot switch to the bypass tray.) GENERAL INFORMATIONUser programs 42 Setting the user programs 1 1 Press and hold the light ( ) key for more than 5 seconds until all ...