Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
It’s really an effective tool to save your money. CIS for EPSON stylus R200/R210/R300/R310 Instruction Thank you for purchasing ST Continuous Ink Supply System. We appreciate your support and will try our best to make your experience with our products a pleasant one. Printing has been a different experience ever since you installed ST Continuous Ink Supply system on your own printer. Just imagining being able to print without regard to the ink level in those expensive little cartridges. Please take your time installing ST Continuous Ink Supply system. Do not remove your old cartridge until you have the ST CIS system primed and ready to install (to prevent the drying of heads). In addition, make sure you are getting perfect nozzle checks before installing the ST CIS system. The ST CIS system won’t be able to work properly if the nozzles are previously clogged. Most people get a perfect nozzle check the first time after installing the ST Continuous Ink Supply system; others may need to run two or three cleaning cycles or let the printer sit for a while before they get the perfect results. 1.General Guide: 1) Components A.CIS system 1 set B. Air filters 6pcs C.Support Arm 1 set D.Refill Kit 6pcs E.Instruction CD 1pc 2) Opening box inspection a.Check whether all the accessories are ready. b.Check whether there's the leakage of the CISS, whether some tubes have been separated from the CISS, whether there are air bubbles in the tube (If there exists more than 20CM air space, please kindly to contact with the local dealer) 2.Printer testing: 1) Check whether the printer is in normal condition, like mechanical status, lubrication status etc. 2) Print testing lines to ensure the printing head is good condition. 3) Print pictures to see whether the printing image is ok. 3.Installation Procedures: 1) First step Put the CISS on the left side of the printer. In the meantime place all the tubes at correct position. Pull out the small rubber plug from the air hole as above picture shown. Place 4pcs of air filters into air holes, the thicker side is down into tank. 2)Second step: Remove cartridge Press the ink cartridge replace Move the cartridge-car to the cartridge Unplug the power button replace position 3) Third step: Set up the Continuous Ink Supply System Replace the spring of the open the cover of cartridge to some Insert screwdriver into the place cartridge-car degree angle that joint cover and cartridge-car Circumgyrate screwdreiver Separate the right side of Take off the cover of cartridge-car deasilly cartridge-car 4) Fourth step: Set up the Continuous Ink Supply System Remove original cartridge Insert our no-sponge cartridge Close the cover for cartridge into printer carefully 5) Fiveth step: Fix Support Arm Tear off the sticker Fix the arm on the 25cm right far from Tear off the sticker you printer Fix the balance arm Tear off the sticker of clamp Attached the clamp on your printer and let it parallel with printer 6) Sixth step : Install tubeline Insert tubelline through the arm Finished 7) Seventh Step: Adjust the tubeline Adjust the tubeline,remove the Make sure tubline will not meet Make sure the lengh of tubline is Cartridge-car back and forth printer when printing enough to reach the far left and right Too long twist Perfect 8) Eighth step Instert the plug Turn on the power switch check wether all thing is usual 9)Nineth step: Nozzle check Usual Broken line ........... The nozzle check patterns are in broken-line, mostly because of small dusk entered into the nozzle, after repeated cleaning, if there is still a few broken line, pls let the printer don’t work about 1 hour, then print the nozzle check pattern, maybe it works well. 4.Reset Procedure: If the indicator light flashing when printing, it tells that you need to reset the chip to full status. Please turn off your printer for about 30 seconds and switch it back on. Ink meter bar shall show full ink. You can start printing as usual. 5.Refill Ink: Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the above picture shown, please use refill kits to fill ink into Reservoir bottles. Carefully pull out the rubber plugs from the refill holes.(there is possibility of ink spattering. Be careful!) Refill ink according to the color in short supply. Then put the rubber back. (Please keep the printer and the reservoir at the same horizontal line during the process of refilling ink.) 6. How to install the cover of cartridge: Pls first install the left side of Then install the other side Adjust well the joint position the cover into cartridge-car Press the right side of cover Finished to make it install well 7.Attention for maintenance: Take out the CISS including the inner cartridges and other components. Then remove support arm from printer, and place the original cartridges in. Please inquire local dealer before sending to maintenance. Notice: 1. Please don’t take out cartridge at random after installing the CIS system. Ke...