Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
• Do not attach any labels, stamps, stickers or similar to the print paper before printing. • When handling the print paper before printing, do not touch the image side (the side where nothing is printed). If there are fingerprints or dust on the print paper or the ribbon, print quality may be degraded. • Be sure to use only the dedicated print paper for this unit. Otherwise malfunction can occur. • Do not fold or crease the print paper. Otherwise malfunction can occur. Push the paper tray all the way in, until it audibly snaps into place. When printing is completed Remove the paper tray from the unit and close the paper tray door. Notes • The printing pack contains a print cartridge for 24 prints and 2 . 12-pack print paper. Only load half of the print paper at one time. • When adding print paper to the paper tray, take care not to exceed the maximum of 12 sheets. Do not mix different types of print papers. Otherwise a paper jam can occur. • Do not write or print anything on the print paper before inserting it into this unit. After printing, if you wish to write onto the image side of the paper, use an oil-based marker. You cannot further print on the image side of the paper. 12 GB 4 Inserting the “Memory Stick” Insert a “Memory Stick” into the unit as shown below. Be sure to push the “Memory Stick” all the way in, until it audibly snaps into place. “Memory Stick” MS ACCESS indicator Insert with cutoff section facing left and arrow at top left. To remove the “Memory Stick” 1 Verify that the MS ACCESS indicator is out. Then push the “Memory Stick” fully into the unit. When you let go, the “Memory Stick” will pop out slightly. MS ACCESS indicator 2 Pull out the “Memory Stick”. Notes • While the “Memory Stick” is being accessed, the MS ACCESS indicator lights up. Do not remove the “Memory Stick” from the unit during this interval. Otherwise the unit and/or the “Memory Stick” may be damaged. • Do not forcibly push or remove the “Memory Stick” into or from the unit. Otherwise the unit and/or the “Memory Stick” may be damaged. • While printing is in progress, do not remove the “Memory Stick” from the unit. Otherwise the unit and/or the “Memory Stick” may be damaged. • The maximum Memory Stick capacity with which this unit is compatible is 128 MB. • For information and precautions regarding the handling of the “Memory Stick”, see the section “Memory Stick” on page 27. Preparations 13 GB Printing Printing Operation During Printing Print paper moves back and forth During printing, the print paper passes four times back and forth between the paper exit slot and the top of the paper tray. When printing is completed, the paper is ejected from the paper exit slot. Print paper • Do not open the print cartridge door or remove the print cartridge from the unit during printing. • Never move the unit during printing, and do not turn off the power. Otherwise a paper jam may occur or the unit may be damaged. If the power was interrupted during operation, turn the power on again and repeat the procedure. Print cartridge door Notes • Place the unit on a flat, level surface for printing. If there is for example a raised section or a wall behind the unit, paper jams can occur. • Before starting to print, make sure that there are no obstructions behind the unit which could block the smooth exit of the paper. There should be a clearance of at least 12 cm. • Do not place any objects on top of the paper tray. • Do not touch the paper during printing, and do not try to pull the paper out. • Do not pull the paper tray out of the unit during printing. 14 GB Printing Images With Print Mark (DPOF Print) This unit supports DPOF (Digital Print Order Format) which enables bulk printing of images on a “Memory Stick” to which a Print Mark has been assigned, for example with a Sony CyberShot digital camera or Handycam camcorder. Assigning a Print Mark 1 Insert the “Memory Stick” into the Sony CyberShot digital camera or Handycam camcorder. 2 Select the image you want to print. 3 Assign a Print Mark as described in the documentation of the camera or camcorder. This information should be found in a section entitled “Selecting Images for Print” or “Assigning Print Marks” or similar. 4 Verify that a Print Mark ( ) is shown with the image on the LCD of the Sony CyberShot digital camera or Handycam camcorder. Bulk printing of images with Print Mark 1 35 2 1Push down the power switch and slide it to the right, to turn the unit on. Push The indication “SETUP” flashes on the display, and then changes to “READY”. Note Do not remove or insert the print cartridge while the “SETUP” indication is flashing on the display. Printing Continued 15 GB 2 Insert the “Memory Stick” into the unit. The highest file number for an image with Print Mark is shown. (Folder number) Number of duplicates File number If a “Memory Stick” that has only one folder is inserted, the folder number is not shown. 3 Press the DPOF button. The unit enters the DPOF mode, and the indicatio...