Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
READ THIS SHEET FIRSTREAD THIS SHEET FIRST Unpack the machine and its components. Check that you have the following: BlackBCI-24 MadeinJapan BCI-24 Madein JapanColor . Machine . Multi-purpose tray . Ink tanks (Black, color) . Power cord . Documentation (Set-Up Sheet, Basic Guide, Registration Card, Extended Service Plan) . Printhead . PCMCIA card adapter . MultiPASS Suite software CD-ROM NOTE • A printer cable is not included. You must purchase a USB cable (less than 16 # / 8 ft./5 m) to connect your machine to a computer. Remove the shipping material from the machine. 1 Place the machine on a flat surface. 2 Remove all shipping tapes from the exterior of the machine. NOTE • DO NOT remove the USB label A at this stage. • Before turning on the power, make sure the document cover A is closed. Attach the multi-purpose tray and load paper. 1 Insert the tabs on the bottom edge of the multi-purpose tray into the holes on the machine as shown. PLEASE WAIT PUT IN CARTRIDGE Co 1 Plug the power cord into a socket. 2 When you connect the machine, the Alarm light blinks, and the messages below should appear in the LCD. 3 If nothing appears in the LCD, press [ON/OFF] to turn on the machine. A Approx. 30 seconds NOTE •Please note that the cartridge (printhead and ink tanks) is installed in steps 5 and 6. USB label A PLEASE WAIT PUT IN CARTRIDGE Co 1 Plug the power cord into a socket. 2 When you connect the machine, the Alarm light blinks, and the messages below should appear in the LCD. 3 If nothing appears in the LCD, press [ON/OFF] to turn on the machine. A Approx. 30 seconds NOTE •Please note that the cartridge (printhead and ink tanks) is installed in steps 5 and 6. USB label A 2 Lift up the tray extension. 3 Place a stack of paper (print side up) in the multi-purpose tray q and adjust the paper guide A to the width of the stack w.Make sure the stack does not exceed the paper limit mark B. A q w B NOTE • When you are not printing, remove the paper stack from the multi-purpose tray and close the tray. 4 Open the paper output tray q, then pull out the tray extension w. Printouts will exit the machine here. q w NOTE • When you are not printing, you can close the paper output tray. Install the printhead. IMPORTANT • To turn off the machine, be sure to always press [ON/OFF].This will ensure that the printhead is capped and prevent it from drying up. • If you are not using the machine for a long period of time,we recommend that you print (in black and color) or clean the printhead approximately once a month to maintain the printhead in good working condition. 1 Remove the tape q, then open the inner cover w. • The printhead holder automatically moves to the left of the machine. IMPORTANT • Do not try to manually move or stop the printhead holder. • Do not touch any metal parts inside the machine. • Do not turn off the machine when opening the inner cover. 2 Remove the printhead from its packaging, then remove the orange protective cap A. IMPORTANT • Do not touch the electrical contacts B. 3 Raise the lock lever C, then gently slide the printhead into the holder. Lower the lock lever. IMPORTANT • Do not touch the lock lever once the printhead has been installed. C B A q w Turn over to continue Install the ink tanks. 1 Start with the black ink tank. Remove the ink tank from its packaging, hold it as shown below, then remove the protective cap A. NOTE •Do not shake or drop the ink tank as the ink may leak and stain your clothes or hands. •Do not attempt to reattach the protective cap A once you remove it. • Once you remove the protective cap A, do not touch the ink port B. B BCI-24Ink Tank Made in JapanBlack A 2 Insert the black ink tank into the right hand slot. Press firmly on the ink tank‘s tab until it clicks into place. BCI-24 Black BCI-24 Black 3 Repeat steps 1 and 2 to install the color ink tank in the left hand slot. BCI-24 Color BCI-24 Black 4 Close the inner cover. Be sure to now align the printhead as explained in step 7. Align the printhead. NOTE • If you will be installing the MultiPASS Suite software, you can also align the printhead from the software. For details, see p. 9-7 of the Basic Guide. 1 When the LCD A displays the following, press [Set]. The machine will print a horizontal line pattern, and the LCD will display: 2 In column A on the printout, note which box has the most solid image. Note the value next to this box and use [2] or [3] on the operation panel to enter it. Then press [Set]. 3 Repeat step 2 for columns B to F. After finishing the setup, the machine returns to standby mode. 100% LTR TEXT PLAIN Ex: Most solid box Least solid box BAD SAMPLE GOOD SAMPLE Column A Value for column A CHANGE H VALUE A 0 ALIGN PRINT HEAD PRESS SET KEY A 100% LTR TEXT PLAIN Ex: Most solid box Least solid box BAD SAMPLE GOOD SAMPLE Column A Value for column A CHANGE H VALUE A 0 ALIGN PRINT HEAD PRESS SET KEY A Install the software. IMPORTANT • DO NOT connect the USB cable before installing the software. NOTE • Windows...