Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Do not install any other print head in any case. It will never work. Installing the Print Head ON 1 Plug the printer in. 2 Turn on the printer. Do NOT turn on the computer yet. The POWER lamp flashes and the printer begins to operate. Wait until the POWER lamp remains fully lit. 3 Open the front cover. The print head holder moves to the centre. 4 Raise the lock lever. Do not touch the inside of the printer other than the lock lever. 4 5 Remove the protective cap from the print head. ^ Notes • Do not touch the print head nozzles or electrical contacts. • Do not attempt to reattach the protective cap once it has been removed. print head nozzles electrical contacts 6 Place the print head in the holder. 7 Lock the print head into place by lowering the lever. Do not touch the lock lever once the print head has been installed. Installing the Ink Tanks A Caution For safety reasons, store ink tanks out of the reach of small children. Do not drop or shake ink tanks. 1 Take out the black ink tank. 5 2 Hold the ink tank as shown in the diagram and remove the protective cap. ^ Notes • Do not shake or drop ink tanks as this may cause the ink to leak out and stain your clothes and hands. • Do not touch the ink port. • Do not attempt to reattach the protective cap once it has been removed. ink port 3 Insert the black ink tank into the right-hand slot. 4 Press the top until it clicks into place. 5 Use the same procedure to install the colour ink tank in the left hand slot. 6 Close the front cover. Wait until the POWER lamp remains fully lit (about 60 seconds). ^ Note You will be notified when ink is low during printing if you enable a low ink warning. For more details about the low ink warning, refer to the User's Guide. 6 im 4 ■ Loading Paper ■ Loading A4 (Letter) Size Plain Paper 3 4 limit mark Open the front cover. Move the paper thickness lever at the top of the print head holder to the left position. Close the front cover. ^ Note Set the paper thickness lever to the left when using plain paper, to the right when using thick paper. Refer to the User's Guide for information on loading envelopes and other media. To avoid paper jams, fan the stack to remove static cling, then align the edges of the stack by tapping it on a flat surface. Load the paper, aligning it with the right side of the sheet feeder. You can load up to 100 sheets of plain paper. Do not exceed this limit. 5 Press the paper guide and slide it against the left side of the stack of paper. You now need to install the printer driver: Windows: Go to page 8 Macintosh: Go to page 10 7 im 5 ■ Installing the Printer Driver ■ Installing the Printer Driver - Windows ^ Notes • Do not disconnect the cable or remove the CD-ROM during the installation. The driver cannot be correctly installed. • The screens below refer to Windows Me installation. Screen may differ depending on the environment you are using. • When installing the printer driver in Windows 2000 or Windows XP, log on to the system as a member of the Administrators group. If the following screen appears automatically, click Cancel and carry out the installation following steps 1 to 7. C,„,l I Back rTSrn M I Special Notes for Windows 98 or Windows Me USB Users Click Cancel to quit the screen and turn off the printer. Next, remove and replace the USB cable connected to your computer. OFF 1 Ensure the printer and computer are switched off. 2 Turn on the computer and start Windows. If any applications automatically run, quit them. Disable any virus detection programs. Do NOT turn the printer on at this stage. 8 Canon Documentation NOP,Hadlivaisinsl*d < 1 Install N“ ] 3 Place the Setup Software & User’s Guide CD-ROM in the CD-ROM drive. H Notes • If the CD-ROM does not run automatically, double-click My Computer in the Windows screen, then double-click the CD-ROM icon. • If the language selection screen appears, select a language, then click the Next button. 4 Follow the instructions displayed on screen. When the screen shown on the left is displayed, click Install. ON 5 When the screen shown on the left appears, turn the printer on. If the printer is recognised, the printer driver will be automatically installed. H’ Note If the connection is not recognised, refer to the section "Notes on Handling the USB Interface (for Windows Users)" on page 21._ 6 Click OK. Before you use the printer, you must carry out print head alignment on page 12. 9 7 When the screen shown on the left appears, click Exit. H- Note • To view the User's Guide, please refer to page 21. • If a message prompting you to restart the computer appears, click Yes. ■ Installing the Printer Driver - Macintosh ^ Notes • Do not remove or insert the USB cable during installation, as this may result in the computer or printer not operating normally. • Before installing the driver, disable all virus detection programs and automatically loading programs or ...