Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If printed on plain paper, a maximum of 100 sheets can be held. Stacker Extender Supports paper stacked in the paper output bin. Face-up Stacker Holds a single sheet of special media (transparency, label, envelope, and heavy weight paper) with print side facing up. Tray Extender Supports paper stacked in the automatic paper feeder. Manual Paper Feeder Used to feed a single sheet of paper. Paper Guides Adjust to the width of paper. Operator Panel 4 Set Up 02-Printing 7/16/99 6:30 PM Page 2 Loading a Stack of Paper For best results, use high quality 75g/m2 (20 lb) xerographic paper. 1. Pull the extender on the automatic paper feeder up, until it stops. 2. Before loading the paper, flex the sheets back and forth to loosen them, then fan them. Tap the edges on a table top to straighten them. Doing this before you load paper helps prevent paper jams. DonOt load too much. This feeder holds up to 150 sheets. 3. Insert the paper in the paper feeder. If the paper has a preferred print side, place the print side facing you. If you use letterhead paper, load the paper with the letter-head edge down and facing you. 12 Set Up 02-Printing 7/16/99 6:30 PM Page 3 4. Adjust the paper guides to the width of the paper. 5. Pull up the extender on the face-down stacker. The face-down stacker can hold up to 100 printed pages. Set Up 13 02-Printing 7/16/99 6:30 PM Page 4 6. ML-5000A users may want to print a self test to check that the printer is working properly. A self test shows current printer configuration. Make sure that the READY light is on. Press and hold the button for about 3 seconds. All the indicators blink. Release the button when each indicator starts to blink in turn. Wait until a self test page prints. ERROR PAPER READY 14 Set Up 02-Printing 7/16/99 6:30 PM Page 5 Installing Printer Driver Windows 95/98/NT4.0 Installation 1. Turn on the computer and start Windows. If Windows 95/98 recognizes the new printer,go to the section OWindows 95/98 Plug and PlayO on page 16. 2.Insert the setup CD-ROM into your CD-ROM drive. If Windows does not automatically run the CD-ROM,go to the sectionOIf Windows Does Not Run the CD-ROMO on page 16. 3.Click on the icon OPrinter Set-upO to install the printer drivers. 4.Click the Item you want to install. 5.Follow the instructions on the screen. Note : WinNT and WinNTRCP item is supported under Windows NT4.0. Set Up 15 02-Printing 7/16/99 6:30 PM Page 6 Windows 95/98 Plug and Play 1.At the ONew Hardware FoundO dialog box,click on the OK button. 2.Insert the setup CD-ROM into your CD-ROM drive. 3.Follow the instructions on the screen. If Windows Does Not Run the CD-ROM 1.Select RUN from the Start menu. 2.Type e:\print32.exe on the command line(Oe:\O is CD-ROM drive),then click OK. 3.Follow the instructions on the screen. Windows 3.1x Installation 1.Insert the CD-ROM disk into your CD-ROM drive. 2.From the Program Manager window,double-click Main, and File Manager 3.From the File Manager window,select your CD-ROM drive, execute print16.exe. 4.Click on the icon OPrinter Set-upO to install the printer drivers. 5.Follow the instructions on the screen. 16 Set Up 02-Printing 7/16/99 6:30 PM Page 7 Installing DOSRCP Utility For DOS Users DOS users should install the Remote Control Panel utility to change print settings. 1. Insert the setup CD-ROM into your CD-ROM drive. 2. At the DOS prompt, type in: c:\>XCOPY e:\Driver\English\DosUtil\*.* c:\DOSUTIL . (Oe:\O is CD-ROM drive)