Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Operating Environment Temperature:10 ~ 32 °C / 50 ~ 90 °F; Humidity: 20 ~ 80 % RH Emulation PCL 6, PCL 5e Fonts 1 bitmap, 45 scalable Interface Switching Automatic (Parallel, USB) Interface • 8PPM (A4) Bidirectional Parallel Standard - Modes supported: Compatible, Nibble, Byte, ECP • USB Interface Standard - USB 1.0 compliant - 12Mbps 1 port Random Access Memory (RAM) 4 MB (expandable up to 68 MB) Fresh Time 1 K (1024 cycles/16 mS) / 2 K (2048 cycles/32 mS) APPENDIX A.1 Paper Specifications Overview This printer accepts a variety of media, such as cut-sheet paper (including up to 100 % recycled fiber content paper), envelopes, labels, transparencies and custom-size paper. Properties such as weight, composition, grain and moisture content are important factors affecting printer performance and output quality. Paper that does not meet the guidelines outlined in this manual can cause the following problems: • Poor print quality • Increased paper jams • Premature wear on the printer, requiring repairs. Notes: • Some paper may meet all of the guidelines in this manual and still not produce satisfactory results. This might be the result of improper handling, unacceptable temperature and humidity levels, or other variables over which Samsung has no control. • Before purchasing large quantities of paper, make sure that the paper meets the requirements specified in this user guide. Always test paper before buying large quantities. CAUTION: Using paper that does not meet these specifications may cause problems for the printer, requiring repairs. This repair is not covered by the Samsung warranty or service agreements. A.2 APPENDIX Paper Specifications Paper Specifications Supported Sizes of Paper Paper Dimensions Weight Capacitya Letter 8.5 . 11 in. (216 . 279 mm) 16 to 24 lb Bond (60 to 105 g/m2) • 150 sheets of 20 lb Bond (75 g/m2) paper for the automatic input tray • 1 sheet of paper for the manual input tray A4 210 . 297 mm (8.3 X 11.7 in.) Executive 7.3 X 10.5 in. (191 X 267 mm) Legal 8.5 . 14 in. (216 . 356 mm) B5 (JIS) 182 . 257 mm (7.2 . 10 in.) Folio 216 . 330 mm (8.5 . 13 in.) Minimum Size (custom) Automatic Input Tray 95 X 127 mm (3.8 X 5 in.) 60 to 163 g/m2 Bond (16 to 43 lb ) • 5 sheets of 20 lb Bond (75 g/m2) paper for the automatic input tray • 1 sheet paper for the manual input tray Manual Input Tray 76 X 127 mm (3 X 5 in.) Maximum Size (custom) 216 . 356 mm (8.5 X 14 in.) Transparency Same minimum and maximum paper sizes as listed above. Thickness: .10 X .14 mm (0.0039 X 0.0055 in.) Labelsb Envelopes up to 90 g/m2 (16-24 lb) a. Capacity may vary depending on media weight and thickness, and environmental conditions. b. Smoothness - 100 to 250 (Sheffield) Note: You may experience some paper jams when using any media with a length of less than 127 mm (5 in.). For optimum performance, make sure you are storing and handling the paper correctly. Please refer to “Printer and Paper Storage Environment” on page A.6. APPENDIX A.3 Paper Specifications Guidelines for Using Paper For best results, use conventional 90 g/m2 (24 lb) paper. Make sure the paper is of good quality, and free of cuts, nicks, tears, spots, loose particles, dust, wrinkles, voids, and curled or bent edges. If you are unsure of what type of paper you are loading (such as bond or recycled), check the label on the package of the paper. The following problems with paper cause print quality deviations, jamming, or even damage to the printer. Symptom Problem with Paper Solution Poor print quality or toner adhesion Problems with feeding Too moist, too rough, too smooth, or embossed; faulty paper lot Try another kind of paper, between 100 ~ 250 Sheffield, 4 ~ 5 % moisture content. Dropout, jamming, curl Stored improperly Store paper flat in its moisture- proof wrapping. Increased gray background shading /printer wear Too heavy Use lighter paper, open the rear output tray. Excessive curl problems with feeding Too moist, wrong grain direction or short-grain construction • Open the rear output tray. • Use long-grain paper. Jamming, damage to printer Cutouts or perforations Do not use paper with cutouts or perforations. Problems with feeding Ragged edges Use good quality paper Notes: • Do not use letterhead paper that is printed with low-temperature inks, such as those used in some types of thermography. • Do not use raised or embossed letterhead. • The printer uses heat and pressure to fuse toner to the paper. Make sure that any colored paper or preprinted forms use inks that are compatible with this fusing temperature (200 °C or 392 °F for 0.1 second). APPENDIX A.4 Paper Specifications Paper Specifications Category Specifications Acid Content 5.5 ~ 8.0 pH Caliper .094 ~ .18 mm (3.0 ~ 7.0 mils) Curl in Ream Flat within 5 mm (.02 in.) Cut Edge Conditions Cut with sharp blades with no visible fray. Fusing Compatibility Must not scorch, melt, offset, or release hazardous emissions when heated to 200 °C (392 °F) for .1 second. Grain Long Grain Moisture Co...