Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
For transparencies, hold them by the edges and avoid touching the print side. Oils from your fingers can cause print quality problems. 3 Load the paper with the side to be printed on facing up. Depending on the media type you are using, keep the following loading guidelines: • Envelopes: Flap side down and with the stamp area on the top left side. If you need to do the printing job with a wrinkled envelopes, open the rear cover, (see page 5.8.) Push the pressure lever on each side down. • Transparencies: Print side up and the top with the adhesive strip entering the printer first. • Labels: Print side up and top short edge entering the printer first. • Preprinted paper: Design side up with the top edge toward the printer. • Card stock: Print side up and the short edge entering the printer first. • Previously printed paper: Previously printed side down with an uncurled edge toward the printer. Note Make sure that you have not loaded too much print material. The print material buckles if you load a stack that is too deep or if you push it in too far. Caution When you print on special material like envelopes, labels, transparencies, or cards, the output location should be the rear cover. Open the rear cover to use it. See page 5.8. 1 pressure lever 1 4 Squeeze the multi-purpose tray paper width guides and adjust 1 Load the paper with the side to be printed on facing up. them to the width of the paper. Do not force too much, or the paper will be bent, which will result in a paper jam or skew. 5 When you print a document, set the paper source and type in the software application. See the Software Section. For information about setting the paper source and type on the control panel, see page 2.3. 6 After printing, fold the multi-purpose tray extension and close the multi-purpose tray. Tips on using the multi-purpose tray • Load only one size of print media at a time in the multi-purpose tray. • To prevent paper jams, do not add paper when there is still paper in the multi-purpose tray. This also applies to other types of print media. • Print media should be loaded face up with the top edge going into the multi-purpose tray first and be placed in the center of the tray. • Always load only the print media specified in page 5.1 to avoid paper jams and print quality problems. • Flatten any curl on postcards, envelopes, and labels before loading them into the multi-purpose tray. • When you print on 76 mm x 127 mm (3 x 5 inches) sized media on the multi-purpose tray, open the rear cover for straight paper path to avoid paper jams. • Make sure to open the rear cover when you print on transparencies. If not, they may tear while exiting the printer. Using manual feed mode You can manually load a sheet of print material in the multi-purpose tray if you select Manual Feed in the Source option from the Paper tab when you change print settings to print a document. See the Software Section. Manually loading paper can be helpful when you want to check the print quality after each page is printed. This loading procedure is almost the same as the procedure for loading in the multi-purpose tray, except you load paper sheet-by-sheet in the tray, send print data to print the first page, and press OK on the control panel to print each following page. 2 Squeeze the multi-purpose tray paper width guides and adjust them to the width of the paper. Do not force too much, or the paper will be bent, which will result in a paper jam or skew. 3 When you print a document, set the paper source to Manual Feed and select the appropriate paper size and type in the software application. See the Software Section. 4 Print a document. The display shows a message prompting you to load paper and press OK. 5 Press Stop. The printer picks up the print material and prints. After one page is printed, the message appears again. Note If you do not press the button, after a pause the printer will automatically pick the print material. 6 Insert the next sheet into the multi-purpose tray and press Stop. Repeat this step for every page to be printed. 5.7
Drucker - ML-3470D (4.23 mb)
Drucker - ML-3471DKG (4.23 mb)
Drucker - ML-3471ND (4.23 mb)
Drucker - ML-3472DK (4.23 mb)