Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Tape Selecting a Location Select a level, stable place with adequate space for air circulation. Allow extra space for opening cover and tray. The area should be well-ventilated and away from direct sunlight or sources of heat, cold, and humidity. See the image below for clearance space. Do not place the printer close to the edge of your desk or table! Clearance Space 954.6 mm(37.5 in.) 100 mm mm(18.8 in.) 482.6 in.) (3.9 100 mm 100 mm (3.9 in.) (3.9 in.) 552 mm(21.7 in.) •Front: 482.6 mm (enough space to allow opening of the paper input tray) •Back: 100 mm (enough space for ventilation) •Right: 100 mm (enough space for ventilation) •Left: 100 mm (enough space for ventilation) 2.3 SETTING UP YOUR PRINTER Installing the Toner Cartridge 2 1 Grasp the front cover and pull it toward you to open. Note: Because the printer is very light, it may be moved when you use it; for example, when opening/closing the tray or installing/ removing the toner cartridge. Be careful not to move the printer. 2 Remove the toner cartridge from its bag and remove the paper protecting the cartridge by pulling the packing tape. SETTING UP YOUR PRINTER 2.4 3 Gently roll the cartridge 5 or 6 times to distribute the toner. Thoroughly rolling the cartridge will assure maximum copies per cartridge. Note: If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into fabric. Cautions: • To prevent damage, do not expose the toner cartridge to light for more than few minutes. Cover it with a piece of paper, if left exposed for more than a few minutes. • Do not touch the green underside of the toner cartridge. Use the handle on the cartridge to avoid touching this area. 4 Locate the cartridge slots inside the printer, one on each side. 2.5 SETTING UP YOUR PRINTER 5 Unfold the toner cartridge handle and grasp it. Insert the cartridge in the printer until it snaps into place. 2 Note: Carefully insert or pull out the toner cartridge not to scratch against the printer. 6 Close the front cover. Make sure that the cover is securely closed. If the cover is not firmly closed, printing errors may occur when you print. Note: When printing text at 5% coverage, you can expect a toner cartridge life of approximately 2,000 pages (1,000 pages for the toner cartridge that is shipped with the printer). SETTING UP YOUR PRINTER 2.6 Loading Paper You can load approximately 150 sheets of paper in the tray. 1 Grasp the paper input tray and pull it toward you to open. Pinch the rear guide and pull it out to extend the tray. Note: Because the printer is very light, it may be moved when you use it; for example, when opening/closing the tray or installing/ removing the toner cartridge. Be careful not to move the printer. 2 Prepare a stack of paper for loading by flexing or fanning them back and forth. Straighten the edges on a level surface. 2.7 SETTING UP YOUR PRINTER 3 Load paper with the print side facing up. 2 Make sure that all four corners are flat in the tray. 4 Pay attention not to overload paper. Paper overloading may cause paper jams. 5 Pinch the rear guide to adjust for the paper length and pinch the side guide and slide it to the left flush against the paper. Notes: • Do not push the width guide far enough to cause the material to warp. • If you do not adjust the width guide, it may cause paper jam. SETTING UP YOUR PRINTER 2.8 6 If necessary, close the paper cover to keep the paper loaded in the tray from dust. Connecting a Printer Cable To print from your computer, you need to connect your printer to your computer with a Universal Serial Bus (USB) cable. Note: Connecting the printer to the USB port of the computer requires a certified USB cable. You will need to buy a USB 1.1 compliant cable that is within 3m in length. 1 Make sure that both the printer and the computer are turned off. 2 Plug the USB printer cable into the connector on the back of the printer. To the USB port on your computer 2.9 SETTING UP YOUR PRINTER 3 Connect the other end of the cable to the USB port on your computer. See your computer User’s Guide if you need help. 2 Turning the Printer on 1 Plug the power cord into the power receptacle on the back of the printer. 2 Plug the other end into a properly grounded AC outlet and turn on the printer using the power switch. To the AC outlet 2 1 Cautions: • The fusing area at the rear portion of the inside of your printer is hot when powered. Be careful not to be burned when accessing this area. • Do not disassemble the printer when it is powered. Doing so may give you an electric shock. SETTING UP YOUR PRINTER 2.10 Printing a Demo Page Print a demo page to make sure that the printer is operating correctly. 1 Press and hold down the Cancel button on the control panel for about 2 seconds to print a demo page. 2 The Demo page shows the printer’s current configuration. 2.11 SETTING UP YOUR PRINTER Installing Printer Software The supplied CD-ROM contains Windows printing software, Linux prin...
Dieses Handbuch ist für folgende Modelle:Drucker - ML-1610 (5.4 mb)
Drucker - ML-1615 (5.4 mb)
Drucker - ML-1620 (5.4 mb)
Drucker - ML-1625 (5.4 mb)