Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Sharp Dateigröße: 4.27 mb Dateiname: Unterrichtssprache:

Page . STATUS MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 . MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Misfeed in the bypass tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Misfeed in the copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Misfeed in the center tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Misfeed in the upper papertray. . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Misfeed in the lower papertray . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Misfeed in the upper exit area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 . TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 4 65 STATUS MESSAGES COPIER TROUBLE? If any of the following messages appears in the display, carry out the prescribed remedy. Message Remedy (Maintenance icon) Maintenance required soon. Service by an authorized SHARP service technician will be required soon. Contact your service center as soon as possible.(This message will be displayed if the information key is pressed when the information ( ) icon is displayed.) Maintenance required. Call for service. Normal maintenance service by an authorized SHARP service technician is needed. Contact your service center. Call for service. A malfunction has occurred which cannot be corrected by the key operator. Contact your authorized SHARP service center for service. (Toner cartridge replacement required icon) Toner is low. Replacement of the toner cartridge will be needed soon. (This message will be displayed if the information key is pressed when the information ( ) icon is displayed.) See page 82. Check the toner cartridge. Check to see if the toner cartridge has been installed properly. Can not continue. Remove paper from the center tray. The number of copies on the center tray has reached the limit. Remove the copies from the center tray. Please check paper in paper tray<.>. Check to see if copy paper has been loaded properly. Load <..> paper into tray <.>. Or cancel job and change the paper size setting. The paper size specified for the tray is different from the actual size. See page 78. Selected paper tray is out of service. Contact your authorized SHARP service center for service. Check stapler or staple jam. Staples become jammed or the staple box is not installed properly (when an optional finisher is installed). Check the staple box. See page 110 for staple jam removal. If the trouble cannot be easily remedied, use key operator program "DISABLE STAPLER" to prevent the use of the stapler until it can be repaired. Contact your authorized SHARP service center for service. KEY OPERATOR See page 19 of the KEY OPERATOR'S GUIDE for enabling/disabling stapler. Please remove paper from the stapler compiler. Paper is left in the stapler compiler. Remove it. See page 112. <.>: paper tray number <..>: paper size to be set 66 MISFEED REMOVAL MISFEED REMOVAL When a misfeed occurs, the copier will stop. The message "Clear paper path." will appear in the display along with an illustration showing paper misfeed locations. . If paper becomes accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. . For misfeeds in optional equipment, see their respective sections of the operation manual. KEY OPERATOR If the backlight change of the display is enabled using a key operator program, the color of the backlighting will change to orange when a misfeed occurs. See page 20 of the KEY OPERATOR'S GUIDE. First confirm the misfeed locations. (p.73) (p.71) (p.67, 68, 72) (p.72) Misfeed in the bypass tray Gently pull the misfed paper out from the bypass tray. 1 4 COPIER TROUBLE? Open and close the side cover to cancel the misfeed display. 2 . You can also cancel the misfeed display by opening and closing the front cover. . Confirm that the misfeed display has been cleared. If the misfeed display is not cleared, remove the misfed paper referring to "A. Misfeed in the paper feed area". 67 MISFEED REMOVAL Remove the misfed paper. 2 Be careful not to tear the misfed paper during removal. If the misfed paper is not seen in step 2, pull out the lower paper tray 3 and remove the misfed paper. Be careful not to tear the misfed paper during removal. Close the paper tray. 4 Close the lower side cover. 5 4 . Confirm that the misfeed display has been cleared. Misfeed in the upper exit area If an optional job separator tray kit or an optional finisher is installed, a misfeed may occur in the upper exit area. COPIER TROUBLE? Open the upper exit area cover. 1 73 COPIER TROUBLE? MISFEED REMOVAL Gently pull the misfed paper out. 2 Close the upper exit area cover. 3 . Confirm that the misfeed display has been cleared. 74 TROUBLESHOOTING TROUBLESHOOTING Always check the message display whenever the copier stops during an operation or operation is ...

Herunterladen

Geben Sie zwei Ziffern: