Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: American Standard Dateigröße: 372.24 kb Dateiname: Unterrichtssprache:

SUGGESTED WHIRLPOOL / BATH INSTALLATION METHODSECURE THE BATH TO THE STUDS AS SHOWN FOR WOOD OR STEEL STUD CONSTRUCTION. TYPICAL FLANGE MOUNTING DETAILUNLESS AN ACCESS OPENING OF AT LEAST12" x 24" (305 x 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED. 1 (4 mm) WHIRLPOOLACCESS PANELUNDER DECK MOUNTING INSTRUCTIONSPlease note that care must be taken to protect the surface of the tub during all aspects of the installation. Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result. 1. Install the tub per the installation instructions provided with the unit. . Prepare the bath deck support structure per the local codes. Note - the bath deck must be self supporting. . Cut bath deck to your specifications. 4. Place the bath deck in position and trace the opening on the tub with a soft pencil. Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result. 5. Remove the bath deck and apply a generous bead of waterproof sealant on the outer edge of the traced line. . Replace the bath deck and secure it into place. 7. Apply additional sealant along the tub and bath deck interface as necessary to ensure a watertight seal. . Remove excess sealant per the manufacturer's instructions. Finished bath deck surface material must be self-supporting and secured per local codesTub support structure per installation instructions provided with the tub Bath deck support materialBathtubWaterproof SealantSTUDWATERPROOF DRYWALL OR CEMENT BOARDWATERPROOF DRYWALL OR CEMENT BOARDTILESEALANTTUBROOFING NAIL 1 x ( 5 x 7 mm) WOODSTRINGER FULL LENGTH 1 x ( 5 x 7 mm) WOODSTRINGER FULL LENGTHSTEELSTUDWASHERTILESEALANTTUB4" (10 mm) DRYWALLSCREW WOOD STUDSSTEELSTUDSTYPICAL INSTALLATION - CORNER PIER CUTOUTSLDrainEnd17" R(4 mm) C -5/1 " R( 44 mm) 1 " R(4 mm) 40" (101 mm) 4" ( 4mm) 70" (177 mm) 57-1/4" (1454mm) 45- /4" (11 mm) 0. 1 0. 0. 5" ( 5mm) Installation of a whirlpool in a platform requires a cutout. Many whirlpools need only a rectangular cutout. Some whirlpools require a more elaborate cutout. Illustrated below are diagrams for those cutouts. MODEL 2351MODEL 2383 All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter. . Grounding is required. The unit should be installed by a licensed electrician and grounded. . Permit access for servicing motor as noted. 4. All building materials and wiring should be routed away from the pump body and heater (if equipped). WHIRLPOOL ELECTRICAL INSTALLATION INSTRUCTIONSELECTRICAL DIAGRAMREAD AND FOLLOW ALL INSTRUCTIONSBLACKWHITE120 VACGND. PUMP/MOTORWIRE SELECTION GUIDEMaximum distance fromfusebox to motorThe sizes shown on thischart are recommendationsfor copper conductorsonly. Always followlocal and nationalelectrical codesMotor Hi PerformanceRating2.1 H.P., 1.4 H.P., and 1.25 H.P. 50'100' 115V Power Line150'200' 121088! The whirlpool should be installed on a 120 vac, 15 amp dedicated GFCI circuit. The circuit should be hard-wired from the electrical power supply panel. The circuit must be a three ( ) wire circuit from the electrical supply panel. A grounded neutral wire and a third wire, earth ground, are essential. Optional heater requires a separate 15 amp maximum GFCI circuit. The whirlpool should be installed on a 120 vac, 20 amp dedicated GFCI circuit. The circuit should be hard-wired from the electrical power supply panel. The circuit must be a three ( ) wire circuit from the electrical supply panel. A grounded neutral wire and a third wire, earth ground, are essential. Optional heater requires a separate 15 amp maximum GFCI circuit. GFCI CIRCUIT REQUIREMENTS:FOR MODEL NUMBERS: 2351237123832466PLEASE SEE THE FOLLOWING TABLE FOR GFCI CIRCUIT REQUIREMENTS: DRAIN CONNECTION AND SYSTEM TESTUsing recommended drain assembly, connect whirlpool drain to waste line in accordance with the drain assembly instructions. Tighten all drain joints securely. Check the pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point " above the top of the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings are factory tightened and inspected, some loosening may have occurred during transit.) Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the whirlpool is running. POST INSTALLATION CLEAN-UPRemove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water an...

Herunterladen

Geben Sie zwei Ziffern: