Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Installation Instructions for use with HyperTerminal™ and serial port Parts List Part Numbers Description IPDACT Internet Communicator-Contact ID only. Requires compatible FL panel equipped with on-board or optional DACT. Requires 300mA aux non-reset able power from FACP. Includes cable from panel primary telco port to IPDACT. IPBRKT Bracket for mounting IPDACT inside MS- 9200UDLS common enclosure or in optional HPP-300ULX power supply IPSPLT Splitter for dual phone lines to IPDACT input cable. ALMSC119 RJ45-DB9F PC serial port programming cable for IPDACT. IPENC Optional cabinet for mounting IPDACT next to compatible Fire-Lite FACP. Use when connecting to older non common enclosure panels such as MS-9200UD or MS-9600. Includes IPBRKT mounting bracket already installed. HP300ULX Optional UL listed Fire Aux power supply for mounting IPDACT next to compatible Fire Panel when additional power is required for IPDACT. Note: All of the above available at Fire-Lite Distribution The IDPACT requires 24VDC filtered regulated power and a phone pair from the DACT of the fire alarm control panel. While not required, it is highly recommended that any customer shared equipment used to connect the IPDACT to the Internet such as router or hub be supplied with backup power from a small UPS. This will provide IP connectivity and reduce central station nuisance alarms if AC power is lost. Checklist of required programming information from Central Station: 1. IPDACT default access password (factory default is 24680). 2. Installer password, required to execute the register command. 3. If STATIC IP is to be used such as in an enterprise or corporation: Obtain IP address, subnet mask and gateway for IPDACT from enterprise IT manager. Default IP is 192.168.0 100 with subnet of 255.255.255.0 4. IPDACT account number or client number 5. IP addresses and of the Primary and Secondary VisorALARM central station receivers 6. UDP Port number to use Mounting Options: Note: a detailed PID (Product Installation Document) is included with the IPBRKT and IPENC. 1. Using Common Enclosure Connect the IPDACT to the fire panel (MS-9200UDLS shown as example but can be followed for the following products: MS-9200UDLS, MS-9050UD, MS-9600LS, MS-5UD-3, MS-10UD-7) 1. Using the instructions found in the IPBRKT kit, install the metal IP Bracket into the right slots of the common enclosure cabinet. 2. Mount the IPDACT onto the IPBRKT using the plastic standoffs that came with the IPBRKT. Screw the standoff through the holes on the IPDACT into the metal mating threaded standoffs on the IPBRKT. Note, discard any double sided tape plastic standoffs that may be included with the IPDACT and use the supplied machine screw versions. 3. Connect 24 VDC from the non-resettable power output of the control panel to the IPDACT terminals marked "GND" and "+12/24VDC". Be careful to observe correct polarity! Run the two conductor power supply wire through the small ferrite ring supplied with the IPDACT. 4. Loop the 8 PIN cable supplied with the IPDACT once through the large Ferrite Ring. Note that this cable is NOT used as an Ethernet Cable but to interconnect the dialer output of the panel to the input of the IPDACT. Plug the 8 PIN cable supplied with the IPDACT into the Primary DACT port of the control panel. Connect the other end of this cable to he IPDACT on terminals marked 'TO AP." 5. Connect the secondary DACT port of the control panel to a standard unpublished RJ-31X phone jack. Note that if the secondary port on the FACP is not used for a backup via POTS line, the IPSPLT can be obtained and used to combine both phone lines. In this case, the cable supplied with the IPDACT connects to the single connector on the IPSPLT (See Panel Manual). 6. Plug one end of the IPDACT Programming Cable (PN ALSMSC120 (shown above or equivalent) into the black RJ45 receptacle on the IPDACT labeled CN1. Plug the other end of this cable into the supplied RS-232 serial adapter that came with the black cable. Plug the adapter into a COM port on your computer. 7. Connect one end of a CAT5 LAN cable into the Ethernet receptacle on the IPDACT as shown below (Green cable) and the other end into an available port on the customer’s LAN hub or switch. Connect serial cable here (CN1) 2. Installation using IPENC or HP300ULX The IPENC is used for mounting the IPDACT next to panels that cannot accept the IPBRKT directly inside the enclosure. Examples of these include the MS- 9200UD and MS-9600. Install the IPDACT onto the factory mounted IPBRKT inside the IPENC using the 4 supplied .”X 6-32 machine screws as shown below. The four black screws will be used to secure the enclosure door following IPDACT wiring connections. For complete information of all installation options, follow the wiring instructions found in the included Product Installation Document. Mount the IPENC next to the FACP as shown in the drawing below. Mounting the IPBRKT inside the HP300ULX when more power is required The IPDACT r...