Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Remove the mounting bracket units, especially if a fire starts in a remote area of the dwelling. If any unit from the base, and attach it to in the series senses smoke, all units will alarm. To determine which Alarm the junction box. initiated an alarm, see table: 2. Using wire nuts, connect the power connector to the During an Alarm: household wiring. On Initiating Alarm(s) Red LED(s) flashes (flash) rapidly STAND-ALONE ALARM ONLY: On All Other Alarms Red LED is Off • Connect the white wire on the power connector to the neutral wire in the junction box. After an Alarm (Latching): • Connect the black wire on the power connector to the hot wire in the junction box. On Initiating Alarm(s) Red LED(s) On for 2 seconds/Off for 2 seconds • Tuck the orange wire inside the junction box. It is used for On All Other Alarms Green LED(s) On, Red LED(s) Off interconnect only. INTERCONNECTED UNITS ONLY: Compatible Interconnected Units Strip off about 1/2” (12 mm) of the plastic coating on the orange wire on the power connector. • Connect the white wire on the power connector to the neutral Interconnect units within a single family residence only. Otherwise all wire in the junction box. households will experience unwanted alarms when you test any unit in the series. Interconnected units will only work if they are wired to in the junction box. • Connect the black wire on the power connector to the hot wire compatible units and all requirements are met. This unit is designed to be compatible with: BRK Electronics® Smoke Alarm Models 9120, • Connect the orange wire on the power connector to the 9120B, SC9120B, 7010, 7010B, 4120, 4120B, 4120SB, 4919, 2002RAC, interconnect wire in the junction box. Repeat for each unit you 100S, 5919, 5919TH; BRK Electronics® Heat Alarm Models HD6135F, are interconnecting. Never connect the hot or neutral wires in the HD6135FB; BRK Electronics® CO Alarm Models CO5120BN, junction box to the orange interconnect wire. Never cross hot and CO5120PDBN; Smoke/CO Alarm Model SC6120B, SC7010BV, SC7010B; neutral wires between Alarms. and First Alert® Smoke Alarm Models SA4120, SA4120B, SA4121B, SA4919B, SA100B. 3. Plug the power connector into the back of the Alarm. 4. Activate the battery back-up by removing the “Pull to Activate Interconnected units must meet ALL of the following requirements: Battery Back-Up” tab. Or, install battery back-up. Battery back-up • A maximum of 18 compatible units may be interconnected cannot work until you install the battery in the correct position (Maximum of 12 Smoke Alarms). (Match “+” to “+” and “-” to “-”). • The same fuse or circuit breaker must power all interconnected 5. Position the base of the Alarm over the mounting bracket, and turn units. the Alarm clockwise (right) until the unit is in place. If wall mounted, adjust unit so words are level. • The total length of wire interconnecting the units should be less than 1000 feet (300 meters). This type of wire is commonly 6. Check all connections. available at Hardware and Electrical Supply stores. • All wiring must conform to all local electrical codes and NFPA 70 (NEC). Refer to NFPA 72, NFPA 101, and/or your local building Improper wiring of the power connector or the wiring leading to code for further connection requirements. the power connector will cause damage to the Alarm and may lead to a non-functioning Alarm. STAND-ALONE ALARM ONLY: • If you are only installing one Alarm, restore power to the junction box. INTERCONNECTED UNITS ONLY: • If you are interconnecting multiple Alarms, repeat steps 1-5 for each Alarm in the series. When you are finished, restore power to the junction box. ELECTRICAL SHOCK HAZARD. Do not restore power until all Alarms are completely installed. Restoring power before installation is complete may result in serious electrical shock, injury or death. 6. Make sure the Alarm is receiving AC power. Under normal operation, the Green power indicator light will shine continuously. 7. If the Green power indicator light does not light, TURN OFF POWER TO THE JUNCTION BOX and recheck all connections. If all connections are correct and the Green power indicator still does not light when you restore the power, the unit should be replaced immediately. 8. Test each Smoke Alarm. Press and hold the Test/Silence button until the unit alarms. When testing a series of interconnected units you must test each unit individually. Make sure all units alarm when each one is tested. A. Unswitched 120VAC 60 Hz source B. To additional units; Maximum = 18 total (Maximum 12 Smoke Alarms) 1. Alarm 2. Ceiling or Wall 3. Power Connector 4. Wire Nut 5. Junction Box 6. Neutral Wire (Wht) 7. Interconnect Wire (Orange) 8. Hot Wire (Blk) If any unit in the series does not alarm, TURN OFF POWER and recheck connections. If it does not alarm when you restore power, replace it immediately. 4 LOCKING FEATURES The locking features are designed to discourage unauthorized removal of the batteries or Alarm. It is not necessary ...