Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
For more security, put one unit in each room. Many or installation in an improper location. Clean the Smoke Alarm as THE PARTS OF THIS SMOKE ALARM powercell, a build-up of dirt, dust or grease on the Smoke Alarm cover, older mobile homes (especially those built before 1978) have little or no This Smoke Alarm alone is not a suitable substitute for complete fire described in “Regular Maintenance,” and test the Smoke Alarm again. insulation. If your mobile home is not well insulated, or if you are unsure detection systems in places housing many people—like apartment of the amount of insulation, it is important to install units on inside walls buildings, condominiums, hotels, motels, dormitories, hospitals, long- If it fails to test properly when you use the test button, or if the problem SMOKE ALARM WITH TEN-YEAR 1. Test/Silence button 1. Mounting bracket only. Smoke Alarms should be installed where temperatures normally term health care facilities, nursing homes, day care facilities, or group persists, replace the Smoke Alarm immediately. NON-REPLACEABLE LITHIUM POWERCELL remain between 40° F (4° C) and 100° F (38° C). WARNING: Test units homes of any kind—even if they were once single-family homes. 2. Power/alarm indicator LED 2. Mounting slots • If you experience frequent non-emergency alarms (like those used in RVs after the vehicle has been in storage, before every trip, It is not a suitable substitute for complete fire detection systems in Model SA340 caused by cooking smoke), try relocating the Smoke Alarm. and once a week while in use. Failure to test units used in RVs as warehouses, industrial facilities, commercial buildings, and special 3. Powercell • If the alarm sounds when no smoke is visible, try cleaning or described may remove your protection. purpose non-residential buildings which require special fire detection relocating the Smoke Alarm. The cover may be dirty. and alarm systems. Depending on the building codes in your area, this 4. Deactivation Tab (located under label) Smoke Alarm may be used to provide additional protection in these • If the alarm no longer sounds during testing, replace the IMPORTANT! PLEASE READ AGENCY PLACEMENT RECOMMENDATIONS 5. Turn to attach to bracket facilities. Smoke Alarm! If the Smoke Alarm was properly activated, and CAREFULLY AND SAVE. TOOLS YOU WILL NEED: had previously alarmed during testing, the powercell is at the NFPA 72 (National Fire Code) Chapter 11 The following information applies to all four building types below: 6. Turn this way to remove from bracket This user’s manual contains This unit is designed to be mounted on the ceiling, end of its service life. (See “Regular Maintenance.”) “For your information, the National Fire Protection Association's In new construction, most building codes require the use of AC or AC/DC important information about or on the wall if necessary. • If the alarm will not silence when you use the Silence feature, Standard 72, reads as follows:” powered Smoke Alarms only. AC, AC/DC, or DC powered Smoke Alarms your Smoke Alarm’s operation. • Pencil • Standard flathead DO NOT IGNORE THE ALARM! This indicates a potentially can be used in existing construction as specified by local building codes. “11.5.1 One- and Two-Family Dwelling Units.” If you are installing this Smoke screwdriver dangerous situation. Refer to NFPA 72 (National Fire Alarm Code) and NFPA 101 (Life Safety • Drill with 3/16” (5 mm) Alarm for use by others, you “11.5.1.1 Smoke Detection. Where required by applicable laws, codes, Code), local building codes, or consult your Fire Department for detailed must leave this manual—or a drill bit • Hammer • If the Smoke Alarm “chirps” about once a minute (for more or standards for the specified occupancy, approved single- and multiple fire protection requirements in buildings not defined as “households.” than 30 minutes), Replace the Smoke Alarm! (See “Regular -station Smoke Alarms shall be installed as follows: (1) In all sleeping copy of it—with the end user. Maintenance.”) This is the low power warning. FOLLOW THESE SIMPLE STEPS! 1. Single-Family Residence: rooms. Exception: Smoke Alarms shall not be required in sleeping DO NOT TRY FIXING THE ALARM YOURSELF—THIS WILL VOID YOUR WARRANTY! rooms in existing one- and two-family dwelling units. (2) Outside of Single family home, townhouse. It is recommended Smoke Alarms be INSTALL THE MOUNTING BRACKET: INSERTING THE POWERCELL: each separate sleeping area, in immediate vicinity of the sleeping installed on every level of the home, in every bedroom, and in each If the Smoke Alarm is still not operating properly, and it is still under 1. To remove the mounting bracket from the warranty, please see “How to Obtain Warranty Service” in the Limited rooms. (3) On each level of the dwelling unit, including basements. bedroom hallway. Smoke Alarm base, hold the Smoke Alarm Exception: In existing one- and two family dwelling units, approved You must activate the powercell before...