Stimmen - 0, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
SILENCING THE END OF LIFE SIGNAL Fuel-burning appliances like: 1. Excessive spillage or reverse venting of fuel appliances caused by WHAT YOU SEE AND HEAR DURING INSTALLATION outdoor conditions such as: 120V PLUG-IN CARBON MONOXIDE ALARM WITH included with this CO Alarm. On each label write in the phone number burning fireplace, gas kitchen Before you start installation, find the pair of self-adhesive labels portable heater, gas or wood This silence feature can temporarily quiet the End of Life warning • Wind direction and/or velocity, including high, gusty winds. Heavy BATTERY BACK-UP AND SILENCE FEATURE HORN: Chirps once of your emergency responder (like 911) and a qualified appliance tech-by pressing the Test/Silence button. The horn will chirp, acknowledging range or cooktop, gas clothesWHEN YOU FIRST INSTALL THE BATTERY: “chirp” for up to 2 days. You can silence the End of Life warning “chirp” air in the vent pipes (cold/humid air with extended periodsnician. Place one label near the CO Alarm, and the other label in the dryer. between cycles). that the End of Life silence feature has been activated. POWER/ALARM LIGHT: Flashes once “fresh air” location you plan to go if the alarm sounds. Damaged or insufficient • Negative pressure differential resulting from the use of exhaust fans. After approximately 2 days, the End of Life “chirp” will resume. After venting: corroded or discon- UNDER NORMAL CONDITIONS (AC POWER): Tools you will need: Screwdriver, drill. approximately 2-3 weeks the End of Life warning cannot be silenced. • Several appliances running at the same time competing for limited nected water heater vent pipe, fresh air. HORN: Silent 1. Determine the best location for your CO Alarm. leaking chimney pipe or flue, POWER/ALARM LIGHT: Shines continuously 2. Your Alarm is equipped to be mounted as a corded unit or a direct or cracked heat exchanger, • Vent pipe connections vibrating loose from clothes dryers, furnaces, or water heaters. plug unit. The unit can be plugged directly into a wall outlet. If your blocked or clogged chimney TESTING AND MAINTENANCE WHEN YOU TEST THE CO ALARM: outlets are mounted horizontally, refer to “If Outlet is Mounted opening. • Obstructions in or unconventional vent pipe designs which can HORN: Sounds loudly - 4 beeps, pause, 4 beeps, pause Horizontally (Sideways)”. amplify the above situations. POWER/ALARM LIGHT: The LED flashes with the same pattern as If the adapter is taken out of the unit, the Alarm can be installed WEEKLY TESTING Improper use of appliance/ device: operating a barbecue 2. Extended operation of unvented fuel burning devices (range, oven, Press the Test/Silence button on the Alarm cover until alarm sounds. the horn. high on the wall, while the adapter is plugged into a wall outlet. grill or vehicle in an enclosed fireplace). 4 beeps, pause. During testing, you will hear a loud alarm sequence – 4 beeps, pause, area (like a garage or screened 3. Temperature inversions, which can trap exhaust close to the ground. Model ACTIVATING THE BATTERY BACK-UP porch). WHAT YOU SEE AND HEAR UNDER DIFFERENT CONDITIONS 4. Car idling in an open or closed attached garage, or near a home. The alarm sequence should last 5-6 seconds. If it does not alarm, make CO606 Activate the battery back-up by Transient CO Problems: “transient” or on-again-off-again CO problems LISTED TO DURING A POWER FAILURE (IN BATTERY BACK-UP): installing the two (2) AA batteries. sure the unit is fully plugged into an unswitched outlet. If the unit still These conditions are dangerous because they can trap exhaust in your can be caused by outdoor conditions and other special circumstances. does not alarm, replace it immediately. home. Since these conditions can come and go, they are also hard to 120V AC ~, UL 2034 HORN: Silent The battery is for back-up only and The following conditions can result in transient CO situations: recreate during a CO investigation. 60 Hz, 0.09A STANDARD POWER/ALARM LIGHT: Flashes once a minute. is not intended to power the Alarm for an extended period of time in • If the Alarm ever fails to test properly, replace it immediately. M08-0206-003 S 08/10 Printed in Mexico WHEN THE ELECTRICITY COMES BACK ON AFTER A POWER FAILURE: the absence of AC. Products under warranty may be returned to the manufacturer for HORN: Silent REGULATORY INFORMATION FOR CO ALARMS replacement. See “Limited Warranty” at the end of this manual. • DO NOT stand close to the Alarm when the horn is sounding. WHAT LEVELS OF CO CAUSE AN ALARM? Why is this important? Because you need to be warned of a potential IMPORTANT! Exposure at close range may be harmful to your hearing. CO problem while you can still react in time. In many reported cases of POWER/ALARM LIGHT: Shines continuously. DIRECT PLUG ALARM INTO AN OUTLET Underwriters Laboratories Inc. Standard UL2034 requires residential CO PLEASE READ CAREFULLY AND SAVE. IF BATTERY BECOMES LOW OR IS MISSING: When testing, step away when horn starts so...