Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Interconnect units within a single family residence only. Otherwise all households will experience unwanted alarms when you test any unit in the series. Interconnected units will only work if they are wired to compatible units and all requirements are met. The wiring shall be in accordance with the provision of Articles 210 and 3003 (B) of the National Electrical Code, ANSI/NFPA 70. The resistance of the interconnecting wiring shall be a maximum of 10 ohms. This unit is designed to be compatible with Model 770LBX in US applications. See for most current interconnect list. Operation: How To Test Testing After Installation 1. Check to see that the green “POWER ON” light is on. The “POWER ON” light is visible behind the slotted case and confirms that the smoke alarm is receiving AC power. 2. Press and hold the test button until the alarm sounds. NOTE: It may be necessary to press the test button for up to 20 seconds for an alarm to sound. An alarm is indicated by a loud pulsating sound, 3 beeps/4sec. Alarm my continue to sound for up to 10 seconds after button is released. 3. At least once a week, press the test button and hold until the alarm sounds, then release. NOTE: Multiple Station Only: 4. Test each alarm separately in the system. 5. Determine that the initiating alarm triggers other alarms in the system. NOTE: Red LED will flash once per second on initiating alarm and once per 45 seconds on interconnected alarms. 7. MAINTENANCE & TROUBLESHOOTING BATTERY REPLACEMENT Batteries should be replaced annually! The Gold Peak 1604A/S/P, Eveready X22, 522, 1222, Duracell MN1604/MX1604 and Ultralife U9VL-J are the only acceptable batteries for use in these smoke alarms. When the battery reaches the end of its normal life, a low battery warning (a single beep every 45 seconds) will sound for up to 30 days to indicate the need for battery replacement. When replacing the battery ensure that the positive and negative terminals on the battery snap positively into the matching terminals in the smoke alarm. TEST THE ALARM WEEKLY. VACUUM EVERY SIX MONTHS Your Smoke Alarm should be cleaned every six months to help keep it working efficiently. REMOVE POWER TO THE ALARM. Gently vacuum through the vents of the alarm with a soft brush attachment. Keep vacuum nozzle from touching the unit. RE-ESTABLISH POWER TO THE ALARM. PROBLEMS MAY BE INDICATED BY THE FOLLOWING: • The alarm does not sound upon pressing the test button. • The alarm does not sound with the smoke test. • The green operating light does not re-mail steadily when unit is AC powered. • The red operating light remains steadily on or off. (i.e. does not flash once every 45 seconds, when the unit is not in alarm.) TRY THE FOLLOWING: • Inspect breaker or fuse in power circuit to alarm. • Gently vacuum as recommended above. • Call an electrician to inspect house wiring and connection to alarms. If these procedures do not correct the problem, do NOT attempt repairs. If the smoke alarm is within warranty period and terms, indicate the nature of the problem and return the unit with proof of purchase. See below for instructions. Units beyond warranty cannot be economically repaired. FALSE ALARMS: Abnormal air conditions may cause the highly sensitive smoke alarm to give a “false” alarm. If no fire is apparent, activate the alarm silencer feature and ventilate the room and/or blow fresh air into the unit until the alarm stops. Once cleared, the smoke alarm will automatically reset. DO NOT DISCONNECT THE AC POWER SUPPLY. Dust can lead to excess sensitivity. Vacuum as recommended above. 8. LIMITED WARRANTY Your American Sensors smoke alarm is warranted for ten years from date of purchase against defects in material and workmanship. BRK Brands, Inc., (“BRK”) the distributor of American Sensors in the United States, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. BRK dealers, service centers, or retail stores selling BRK products do not have the right to alter, modify or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes or any batterie...