Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Kidde Dateigröße: 173.09 kb Dateiname: Unterrichtssprache:

When choosing your installation locations, make sure you can hear the alarm from all sleeping areas. If you install only one CO alarm in your Recommended Locations home, install it near bedrooms, not in the basement or furnace room. • When wall mounting, place out of reach of children. Under no circumstances should children be allowed to handle the CO alarm. Locations To Avoid IMPORTANT: Improper location can affect the sensitive electronic components in this alarm. To avoid causing damage to the unit, to provide optimum performance, and to prevent unnecessary nuisance alarms: • Do not install in kitchens, garages or furnace rooms that may expose the sensor to substances that could damage or contaminate it. • Do not install in areas where the temperature is colder than 40°F (4.4°C) or hotter than 100°F (37.8°C) such as crawl spaces, attics, porches and garages. • Do not install within 5 ft. of heating or cooking appliances. (Kidde recommends 15 ft. to prevent nuisance alarms). • Do not install near vents, flues, chimneys or any forced/unforced air ventilation openings. • Do not install near ceiling fans, doors, windows or areas directly exposed to the weather. • Do not install in dead air spaces, such as peaks of vaulted ceilings or gabled roofs, where CO may not reach the sensor in time to provide early warning. • Do not install this unit near deep-cell large batteries. Large batteries have emissions that can cause the alarm to perform at less than optimum performance. • Do not obstruct the vents located on the alarm. Do not place the alarm where drapes, furniture or other objects block the flow of air to the vents. • Do not install on a switched or dimmer-controlled outlet. 6. KN-COB-DP-LS Operating Characteristics 4. Installation Instructions 6. KN-COB-DP-LS Operating Characteristics 4. Installation Instructions How to Install Your Alarm Direct Plug Alarm To install: 1. Choose a standard 120V unswitched outlet to plug the alarm into. 2. If outlet is mounted sideways (horizontally), rotate the plug and plug the alarm in. 90. ROTATING DIRECT CAUTION: Do not rotate the alarm while it is plugged into an outlet, as damage to plug may PLUG result. Important Labels Provided Two labels have been provided that have important information on what to do in case of an alarm. Add the phone number of your emergency service provider in the space provided. Place one label next to the alarm after it is mounted, and one label near a fresh air source such as a door or window. 5. Alarm Characteristics Carbon Monoxide Alarm Indicator When the alarm senses a dangerous level of CO, the unit will emit a loud alarm pattern. The alarm pattern is 4 quick beeps followed by 5 seconds of silence. This cycle repeats as long as a dangerous CO conditions exist. The red Alarm LED will flash the same pattern (and the PPM will be displayed on alarms with digital displays). WARNING: When powered by battery backup only; after four minutes, the alarm will sound and flash only once every minute, until the alarm is reset or the CO is eliminated. If the unit is unplugged it will produce a constant tone until the battery is removed or the unit is plugged back into the wall unless the Tamper- Resist feature has been deactivated or disabled. WARNING: If at any time you test the alarm and it does not perform as described, have it replaced immediately. 6. KN-COB-DP-LS Operating Characteristics When you first power up the alarm: The red Alarm LED will light and the alarm will sound briefly, then the green Operate LED will light. This indicates that the CO alarm is receiving power and that the alarm circuit is functioning. Within a few minutes, your carbon monoxide alarm will start monitoring for CO and will continue to do so as long as it receives power. When the Model KN-COB-DP-LS CO alarm loses power: If you have a good 9V battery installed, the alarm will automatically switch to the battery backup mode and the green LED will flash approximately every 10 seconds. The unit will continue to operate normally and detect CO for at least 20 hours. When the Model KN-COB-DP-LS CO alarm loses power: If you have a good 9V battery installed, the alarm will automatically switch to the battery backup mode and the green LED will flash approximately every 10 seconds. The unit will continue to operate normally and detect CO for at least 20 hours. If the battery is low or missing, or if the unit malfunctions, it will alarm differently to alert you of specific conditions. Please familiarize yourself, and other family members, of the difference between a CO alarm and an indication signifying a problem with the unit. When AC power is restored, the alarm will automatically switch back to normal operating mode and the green LED will come on continuously. Observe the CO alarm regularly to make sure the green Operate LED is on, indicating normal operation. If the green Operate LED is not on, unplug the CO alarm, then plug it in again. This will clear the alarm for restart. ...

Herunterladen

Geben Sie zwei Ziffern: