Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Bosch Dateigröße: 100.12 kb Dateiname: Unterrichtssprache:

When you press an incorrect key, a flat buzz tone sounds to indicate an invalid entry. 6. Faulted Point: When you enter an arming command, and a point is faulted, the sounder is activated for 2 seconds. The point status indicator associated with the faulted point is lit. 7. Watch Tone: When the Watch Mode is activated, the keypad emits a brief tone to alert you when any watch point is faulted and the point indicator lights to indicate which point is faulted. The tone sounds only when the door or window is opened. It does not sound again for that point until the door or window is closed and then reopened. Some system trouble events produce a trouble tone without producing any status light indications. These trouble events fall into three categories: 1. Hardware, software, or wiring problems. For example: a keypad was unplugged from the control panel or the printer was unplugged. Call your security company. 2. Communication or phone failure. For example: you have phone line trouble. Call your security company. 3. Late to close reminder tone. If your system is programmed to send a Closing Report, your keypad sounds the trouble tone to remind you that it is time to close. Arm your system to silence the tone. Turn the Entire System On With Delays . I have this feature. . I do not have this feature. . This feature requires a passcode. Command 1 is used to arm the entire system, both perimeter and interior points. Once you enter Command1, the exit delay time starts. You now have a predetermined amount of time to exit the protected area before the system arms. During the exit period, you can move through motion detectors or any protected area on your way to any exit without causing an alarm. To cancel Command 1, enter your personal passcode and press [ENT]. Note: If you leave the building after the exit time expires, you can begin the entry delay or initiate an alarm. It this happens, disarm your system by entering your personal passcode and press [ENT]. It your system reports to a central station, call them if an alarm occurs. Application Command1 is useful in applications where you want your cleaning or service personnel, or anyone else to arm your system when they leave, but you do not want them to have the passcode to disarm the system. Command 1 arms the system, but does not disarm the system. COMMAND 1 Arming with COMMAND 1: 1. Ensure all points are secure. All of the Point Status indicator lights on the Keypad should be off. If not, refer to Force Arming the System on page 29. 2. Press the [COMMAND] bar. The Command mode indicator light comes on. 3. Press the [1] key. The PERIMETER indicator and the INTERIOR indicator lights begin to flash on and off, showing the system has begun exit delay time. 4. To disarm your security system or cancel COMMAND 1, enter your personal passcode and press [ENT] before the delay time expires. Turn the Entire System On Without Delays . I have this feature. . I do not have this feature. . This feature requires a passcode. Use this function to turn on the entire system, both perimeter and interior without delays. When entering Command 11, remember that the second [1] must be pressed within 2 seconds of pressing the first [1]. COMMAND 1 1 Using Command 11: 1. Ensure all points are secure. All Point Status indicator lights on the keypad should be off. If not, see the section describing Force Arming the System (on page 29). 2. Press the [COMMAND] bar. The Command mode indicator light comes on. 3. Press the [1] key. Now press the [1] key again. 4. The PERIMETER, INSTANT, and INTERIOR lights come on, showing the perimeter, instant, and interior points are armed without entry/exit delay time. 5. To disarm your security system, enter your personal passcode and press [ENT]. Turn On the Perimeter With No Delays . I have this feature. . I do not have this feature. . This feature requires a passcode. Command 2 is used to arm only the perimeter of your building, leaving the interior of the building disarmed. This command allows no exit or entry delay time through the perimeter, including the designated delay door. Enter your personal passcode, plus [ENT], to cancel Command 2. Remember, there are no entry or exit delays when you use this function. You must disarm (turn off) the system to enter or exit the premises. Application This arming command is useful in residential systems at night when everyone is home and ready to retire for the evening. In commercial installations, this arming command is useful when you are working late and you want the perimeter of the building armed until you are ready to leave. COMMAND 2 Arming with COMMAND 2: 1. Ensure all perimeter points are secure. Interior points are not armed with this command, and can remain faulted while arming with Command 2. Perimeter point status lights should be off. If not, refer to Force Arming the System on page 29. 2. Press the [COMMAND] bar. The Command mode indicator light comes on 3. Press the [2] key. The PERIMETER and INSTANT...

Herunterladen

Geben Sie zwei Ziffern: