Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Firex Dateigröße: 142.52 kb Dateiname: Unterrichtssprache:

WARNING: This smoke alarm should be installed only by a qualified electrician. Smoke alarm installation must be in accordance with the requirements of Article 760 of the National Electrical Code and any local codes that may apply. THIS SMOKE ALARM SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION’S STANDARD 72 (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269). • Install smoke alarm on a 4-inch octagon or single gang junction box only. 1. From back of smoke alarm, remove mounting plate. (To later engage tamper-resist feature, twist out and set aside one of the pins molded into plate. Both pins are exactly the same.) 2. Align recessed slots on plate with mounting holes of a 4inch octagon or single gang junction box. 3. Gently pull household wires through center hole of plate. 4. Secure plate to junction box with mounting screws. 5. With a small wire connector, connect white wire from connector plug to white household wire. 6. Connect black wire from connector plug to black household wire. 7. If interconnection is desired, connect yellow wire from connector to interconnect wire between smoke alarms. See section INTERCONNECTING SMOKE ALARMS. NOTE: If this will be a single-station smoke alarm, cover yellow wire with electrical tape and tuck into FPAD junction box. 8. Attach connector plug to pins on back of smoke alarm. Plug will only fit one way and will snap into place. 9. Gently tug connector to be sure it is attached securely. Remove thin plastic 4 Battery Battery Door 10. Position smoke alarm to mounting plate and turn clockwise to lock into place. For tamper-resist, use long-nosed pliers to remove thin plastic Insert pin here Remove pin from here from notch on smoke alarm edge. Insert pin into notch on edge of smoke alarm after smoke alarm is positioned properly in base. 11. If the alarm has a red arrow tab in the battery compartment, remove it and close the battery door. If not, just close the battery door. Smoke alarm may beep briefly as door is closed. 12. Turn on power at main fuse box or circuit breaker. 13. Test smoke alarm. See “TESTING THE SMOKE ALARM.” INTERCONNECTING SMOKE ALARMS • FOR INTERCONNECT LINE ONLY use #14-#18 AWG minimum solid or stranded wire. When interconnecting, maximum wire length between any two is 1,500 feet for #18 AWG or 4,000 feet for #14 AWG (20 OHMS loop resistance). • This smoke alarm may be interconnected with as many as 11 additional Firex model AD, ADC, PAD, FADC, and FPAD smoke alarms, and/or as many as 6 Firex model ADH heat alarms for a total of not more than 18 interconnected devices. DO NOT connect to any type or model smoke alarm. • Connect smoke alarms to a single AC branch circuit. If local codes do not permit, be sure the neutral wire is common to both phases. WHITE WHITE WHITE YELLOW YELLOW BLACK BLACK BLACK TO NEUTRAL TO 120 VAC FOR INTERCONNECT: USE # 18 AWG MINIMUM WIRE RED AND GREEN LED INDICATORS This smoke alarm features separate red and green LED indicators. The LEDs indicate the following: GREEN CONSTANT ON — AC power is present. GREEN OFF — AC power is not present. RED blinks once a minute — Indicating presence of a working battery. RED blinks once a second — Smoke alarm senses smoke and simultaneously sounds an audible alarm. RED OFF — Another smoke alarm in the network has sensed smoke and is signalling this alarm. (Interconnected system only) TESTING THE SMOKE ALARM ! WARNING • Test each smoke alarm to be sure it is installed correctly and operating properly. • Test all smoke alarms in an interconnected system after installation. • The Push-to-Test button accurately tests all functions. DO NOT use an open flame to test this smoke alarm. You may ignite and damage the smoke alarm or your home. • Test smoke alarms weekly and upon returning from vacation or when no one has been in the household for several days. • Stand at arm’s length from the smoke alarm when testing. The alarm horn is loud to alert you to an emergency and can be harmful to hearing. Test all smoke alarms weekly by doing the following: 1. Observe the green LED. A constant green light indicates the smoke alarm is receiving 120V AC power. 2. Firmly depress the Push-to-Test button for at least five (5) seconds. The smoke alarm will sound 3 short beeps followed by a 2-second pause and then repeats. The alarm may sound for up to 10 seconds after releasing the Push-to-Test button. NOTE: If smoke alarms are interconnected, all smoke alarms should sound an alarm within three seconds after any test button is pushed and the tested smoke alarm sounds. 5 3. If smoke alarm does not sound, turn off power at main fuse box or circuit breaker and check wiring. Retest smoke alarm. REPLACE OR RETURN THE ALARM IF THE PUSH-TO-TEST FUNCTION DOES NOT OPERATE PROPERLY AFTER FOLLOWING THE PROCEDURES OUTLINED ABOVE (see REPAIR below). ! DANGER: If alarm horn sounds, and smoke alarm is not being tested, the smoke alarm is sensing smoke. THE SOUND OF THE AL...

Herunterladen

Geben Sie zwei Ziffern: