Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
An installed smoke alarm must be removed or covered fully (with a plastic bag or similar) before renovations begin. 'Ei Electronics 2003 P/N B15026 R0 RADIO SMOKE ALARMS with WIRELESS INTERCONNECT INSTRUCTION LEAFLET Contains vital information on unit operation and installation. Read and retain carefully. If you are just installing the unit, this leaflet MUST be given to the householder. MODELS: Ei 405 - Replaceable 9V Battery Ei 405C - Replaceable 9V Battery & hard wired interconnect option Ei 405TY - 10 Year Lithium Batteries built-in Ei 405TYC - 10 Year Lithium Batteries built-in & hard wired interconnect option All with Optical Smoke Sensor1 1. READ THIS FIRST A Smoke Alarm is an early warning device. Used correctly it can give you and your family valuable extra time to escape. . Models Ei405 & Ei405C - connect battery snaps firmly (see fig 1b). Press the test button and horn should sound. . Models Ei405C, Ei405TY & Ei405TYC - slide unit on to mounting plate to connect the batteries. . When the battery is first connected the Alarm may sound for 2-3 seconds and/or the red light may flash quickly for 10 seconds - this is normal. . A Smoke Alarm does not prevent fires. . Install correctly, in the centre of the ceiling if possible. . Test weekly. 5 WAY PLUG ENGAGES SOCKET ON MOUNTING PLATE TO CONNECT BATTERIES & HARD WIRING INTERCONNECT (Ei 405TY, Ei 405TYC & Ei 405C only) Figure 1a Figure 1b 2 . If the Alarm beeps without the red light flashing at the same time then clean unit as this is the automatic test feature indicating the chamber is degraded. . Plan your escape route. . Proper protection usually requires more than one Smoke Alarm. . If you have any doubt or query about Smoke Alarms consult the supplier or your local Fire Brigade. . Models Ei405TY & Ei405TYC - When the Alarm beeps and the red light flashes at the same time or the blue light flashes every 9 seconds it indicates the battery is depleted and the entire alarm must be replaced. This normally occurs after 10 years has elapsed. . Models Ei405 & Ei405C - When the Alarm beeps and the red light flashes at the same time replace the battery (see fig 1). The wireless interconnect will operate as received once the batteries are connected. (Program units if nearby systems are likely to cause false alarms). 2. INTRODUCTION Congratulations on purchasing Ei405 Radio Smoke Alarms. You can easily install these alarms throughout the house in closed rooms, corridors and in the attic for the fastest response to developing fires. Closed doors are great for slowing down the spread of fire, but unfortunately they can also greatly slow down the response time of alarms, as they block the smoke getting to them. Without interconnection, closed doors also greatly reduce the alarm sound level throughout the house, so even though the fire is detected early, the alarm may not be heard. The Ei405 Radio Smoke Alarms offer the comfort of interconnection without the hassle of installing the interconnect wires. The wireless interconnect helps ensure the alarm will be heard everywhere - including most importantly, the bedrooms. The wireless interconnect will operate as received once the batteries are connected. To check operation, first connect all the batteries (see section 1) and then hold down the test button on the first unit until the blue light comes on continuously for 3.5 seconds. All the other smoke alarms will respond within 5 seconds. If there is any possibility of a neighbour having a similar system, you should program your units so your system will not cause his/hers to alarm or vice versa. This is easily done and only takes a few minutes- see below (section 6.3). A remote control Ei410 is available to allow you to test and hush the alarms, without having to reach up to the smoke alarms on high ceilings. The remote control also has a "Locate" button to identify the unit causing the alarm - this is 3 excellent, particularly at night, as it rapidly identifies where the fire is located. This is ideal for larger systems as the disturbance in the house can be kept to a minimum e.g. no need to enter all the bedrooms to check to see if the red light is flashing rapidly. 3. LOCATING YOUR SMOKE ALARM Sufficient smoke must enter your Smoke Alarm before it will respond. Your Smoke Alarm needs to be within 10 paces (7.5 metres) of the fire to respond quickly. The smoke alarms need to be in positions where they can be heard throughout your home, so they can wake you and your family in time for you all to escape. A single Smoke Alarm will give some protection if it is properly installed, but most homes will require two or more to ensure that a reliable early warning is given. For maximum protection you should put individual Smoke Alarms in all the rooms where fire is most likely to break out. Your first Smoke Alarm should be located between the sleeping area and the most likely sources of fire (living room or kitchen for example). But it should not be more than 10 paces (7.5...
Dieses Handbuch ist für folgende Modelle:Alarm - Ei 405TY (878.72 kb)
Alarm - Ei 405TYC (878.72 kb)