35' Max. 25 1/4" From Inside-Front Frame Toekick 22 5/8" 3 3/16" 34" Min. 35" Max. Underside of Countertop to Floor , This Wall Area Must be Free of Pipes or Wires 1-3/4- 24" Min. Revised 7/97 Plumbing and Electric Service Must Enter Inside This Area -23-5/8" Min.- 24" Max. Кыиии; Design Information: This dishwasher provides a stainless steel appearance, both inside and outside. A toekick is supplied and may be covered with a custom toekick to match kitchen decor. Side trim is n

The rear legs should be screwed in flush with the bottom support, as shipped. The front of the dishwasher must be shimmed to level it. Water and electrical must be routed through the back wall. Electrical Requirements The dishwasher must be supplied with 120V, 60Hz, and connected to an individual properly grounded branch circuit protected by a 15- or 20-amp circuit breaker or time-delay fuse. The dishwasher must be installed so that the drain hose is no more than 10 feet in length for proper

The rear legs should be screwed in flush with the bottom support, as shipped. The front of the dishwasher must be shimmed to level it. Water and electrical must be routed through the back wall. Electrical Requirements The dishwasher must be supplied with 120V, 60Hz, and connected to an individual properly grounded branch circuit protected by a 15- or 20-amp circuit breaker or time-delay fuse. • The dishwasher must be installed so that the drain hose is no more than 10 feet in length for prope

• Water and power supply should enter in the shaded area. • Electrical and water connections are at the right front of the dishwasher. The hot water line should extend forward 30" to 40" from the rear wall. The electrical must extend forward at least 24" to reach the junction box. • To prevent siphoning, an air gap must be used when the waste tee or disposer connection is less than 18" above the floor. Cabinets Square and Plumb Floor MUST be Even with Room Floor This Wall Area must be Free of Pi

• The handle should be installed so that it aligns with adjacent drawer handles, or 4-1/2" max. from the top of the panel. Secure the handle in the same manner as cabinet handles. Screws must be countersunk into the panel. STEP 6 INSTALL ASSEMBLED PANEL • Secure the panel to the door by inserting the top and bottom mounting screws with spacers into the matching keyhole slots. • Make sure all 4 spacers engage the keyhole slots. • Press the panel against the door and push downward until the spacer

This should last about 3 months. Fill as needed. If you accidentally spill: Wipe up the rinse agent with a damp cloth. Don’t leave the spill in the dishwasher. It can keep your detergent from working. If you can’t find any rinse agent, write: BENCKISER CONSUMER PRODUCTS, INC. (‘‘JET-DRY’’) Corporate Centre 1 55 Federal Road P.O. Box 1991 Danbury, CT 06813-1991 Forget to Add a Dish? Add dishes any time during the RINSE & HOLD cycle. With other wash cycles, you can add dishes at any time BEFORE th

• Failure of the product if it is abused, misused, or used for other than the intended purpose or used commercially. • Damage to product caused by accident, fire, floods or acts of God. • Incidental or consequential damage to personal property caused by possible defects with this appliance. • Cleaning or servicing of the air gap device in the drain line. WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential dam

Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT — Save these instructions for local inspector’s use. Observe all governing codes and ordinances. • Note to Installer — Be sure to leave these instructions with the Consumer. • Note to Consumer — Keep these instructions with your Owner’s Manual for future reference. • Skill Level — Installation of this dishwasher requires basic mechanical and electrical skills. Proper installation is the responsibili

• All models have a full length door without the traditional access panel. • These dishwashers may be installed beneath countertops of stone or other materials that will not accept screws. No trim kit required. *Dishwasher models ZBD6890 and ZBD0700 require a 3/4” thick custom panel and will be 24-3/4” deep. Figure A 4 Installation Preparation DRAIN REQUIREMENTS • Follow local codes and ordinances. • Do not exceed 10 feet distance to drain. • Do not connect drain lines from other devices to the

STEP 11 Check Level Side To Side Check Level Front to Back Turn Legs to Adjust Access Hole Figure W Figure X 11 Installation Instructions SECURE DISHWASHER TO CABINET STEP 12 The dishwasher must be secured to the countertop or the cabinet sides. When countertops are made of wood, use Method 1. When countertops are granite or other materials that will not accept screws, use Method 2 to secure dishwasher at the sides. IMPORTANT — After leveling, verify that the dishwasher is still in the correct p