Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
-Carefully dispose of the packing material. -After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. -The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. -The appliance is not intended for use by young children or inform persons without supervision. -Young children should be supervised to ensure that they do not play with the appliance. -Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open. -This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements. -Do not touch the heating element during or after a wash cycle. -Do not lean or sit on the door when it is open, as this could over turn the dishwasher. -If the appliance malfunctions, turn off the water supply to the appliance and disconnect the plug from the wall socket. Then, consult the section entitled, "Troubleshooting." If you cannot solve the problem, contact an authorised service agent. -Only authorised service agents can make repairs. -Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. -If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. -After installation, the power plug must be accessible. -Fundamental rules to follow when using the appliance: * Never touch the dishwasher when barefoot or with wet hands or feet; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be excessively or dangerously bent or flattened; * If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply. To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: -call only the Service Centers authorized by the manufacturer. -always use original Spare Parts Close-up View (control panel) A ON-OFF Button G Cycle select button B ON-OFF Light H Cycle indicator light C 1/2 load Button I Start/Pause button D 1/2 load indicator light J Low Rinse Aid Indicator Light E Delay select Button K Low Salt Indicator Light F Display delay time L Handle For Opening Door .1. GB Close-up View (Interior) Close-up View (Interior) A Upper Rack F Washing Filter B Rack Height Adjustor G Detergent and Rinse Aid Dispenser C Top Spray Arm H Salt Container Cap D Lower Rack I Third Sprayer E Bottom Spray Arm Technical characteristics Width 60cm Depth 60cm Height 85cm Capacity 12 standard place settings Mains water pressure 0.03-0.6MPa Power voltage 220-240V~50Hz Total absorber power 2150W GB .2. Salt Salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Adjusting Salt Consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimise and customise the level of salt consumption so that it remains at a minimum. Your local Water Board can supply the degree of hardness of the water in your area. Loading the Salt into the Softener Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: -Remove the lower rack and then unscrew and remove the cap from the salt container; -If you are filling the container for the first time, fill it with water; -Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. -Carefully screw the cap back on. To adjust salt consumption, proceed as follows: -Unscrew the cap from the salt container; -There is a ring on the container with an arrow on it (see figure to The salt container must be filled when the "low salt" indicator light (located on the control panel) comes on. To prevent the formation of rust, load the salt just before beginning a wash cycle. the side), If necessary, rotate the ring in the anticlockwise direction from the "-" setting towards the "+" sign, based on the hardness of the water being used. It is recommended that adjustments be made in accordance with the following scheme: Water Hardness Level Clarke degrees .dH mmol/l Selector position Salt consumption (Grams/cycle) Autonomy (cycles/2kg) 1 014 MNT MNIT L M L 2 NQPS NUQQ NIUQIQ =?J? OM SM 3 PSTN QRUV QIRUIV jba QM QM 4 [TN [UV [UIV ?H? SM OR .3. GB Detergent and Rinse AidDetergent and Rinse Aid Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start...