Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
If you received a damaged dishwasher, you should immediately contact your dealer or builder. Optional Accessories – See the Owner’s Manual for available custom panel kits. FOR YOUR SAFETY Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing installations described in this booklet, gloves and safety glasses should be worn. IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions for the consumer and local inspector’s use. • Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. • Skill Level – Installation of this dishwasher requires basic mechanical, electrical and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See warranty information. • Completion Time – 1 to 3 Hours. New installations require more time than replacement installations. GSD2000 READ CAREFULLY. KEEP THESE INSTRUCTIONS. 206C1559P195 31-30255 07-09 JR PARTS SUPPLIED IN INSTALLATION PACKAGE: ¦ Two 8-18 x 5/8" Phillips-head wood screws ¦ Junction box cover and #10 hex head screw ¦ Drain hose (78" long) and hose clamp ¦ Cord protector (Power Cord Models Only) ¦ Conversion leads (Power Cord Models Only) ¦ Literature, product samples and/or coupons Screw Kit #10 Hex Head Junction Box Screw 1/2" long #8 Phillips-Head Wood Screws 5/8" long Junction Box Cover Cord Protector Conversion Leads 78" Drain Hose Hose Clamps Cord Protector (Power Cord Models Only) Conversion Leads (Power Cord Models Only) Hose Clamp MATERIALS YOU WILL NEED: ¦ WX09X70910 power cord if applicable to your installation ¦ UL-Listed wire nuts (3) ¦ Thread seal tape ¦ 90° elbow, ferrule and compression nut – (3/8" NPT external thread on one end and opposite end sized to fit water supply) ¦ GPF65 Side-mount bracket kit for use with granite countertops For New Instalations : ¦ Electrical cable ¦ Water line–3/8" minimum copper tubing ¦ Strain relief for electrical connection ¦ Hand shut-off valve (recommended) ¦ Air gap for drain hose, if required ¦ Waste tee for house plumbing, if applicable ¦ GPF10S drain hose (10' long), if needed ¦ Screw-type hose clamps Hot Water Line Wire Nuts Electrical Cable Hot Water Line–3/8" Minimum Copper Tubing Electrical Cable or WR09X70910 Power Cord 3 Wire Nuts 90 . Elbow 307Dia11 Tape Shut-Off Valve Thread Seal Tape 90° Elbow, Ferrule and Compression Nut Strain Relief Air Gap Hose Clamps Optional 10' Drain Hose GPF10S GPF65 Side-Mount Bracket Kit Waste Tee Air Gap Screw-Type Hose Clamps TOOLS YOU WILL NEED: ¦ Safety glasses ¦ 1/4" and 5/16" nutdrivers ¦ Flashlight ¦ Gloves ¦ Adjustable wrench (6”) ¦ Phillips-head screwdriver ¦ Measuring tape ¦ Level ¦ Carpenter’s square ¦ Bucket to catch water when flushing water line ¦ Tubing cutter ¦ 15/16" socket wrench For New Instalations : ¦ Hole saw set ¦ Drill and appropriate bits Nutdriver Hole Saw Bit Safety Glasses Flashlight Crescent Wrench 1/4" and 5/16" Nutdrivers Safety Glasses Flashlight Hole Saw Set Phillips-Head Screwdriver Screw Driver II Drill & Bits Adjustable Wrench Carpenters Square Drill and Bits Gloves Measuring Tape Level 2 Level Carpenter’s Square Measuring Tape Tubing Cutter Bucket Tubing Cutter 15/16" Socket Wrench Bucket 2 Installation Preparation – Enclosure PREPARE DISHWASHER ENCLOSURE #282 French WARNING To reduce the risk of shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. Clearances: In a corner installation, provide at least 2" clearance between the dishwasher and the adjacent cabinet, wall or other appliance. Provide at least 27" of clearance in front of the dishwasher. 2" Minimum Countertop Dishwasher 27" Minimum 05A-1183F #282 French #282 French ADVERTENCIA Para reducir el riesgo de choque, incendio o lesion a personas, el instalador se debe cerciorar de que la lavadora este completamente cerrada en el momento de la instalacion. • The rough cabinet opening must have a minimum width and depth of 24" and height of 34-1/2" ± 1/4" from the floor to the underside of the countertop. • The back wall should be free of pipes or wires. • Adjacent cabinets should be square and plumb to ensure a good fit. Refer to Figure A. • For a corner installation, allow 2" minimum clearance between the dishwasher and the adjacent wall. • Provide at least 27" in front of the dishwasher to allow the dishwasher door to open fully. Refer to Figure B. Figure B Figure A • Make sure the floor is level inside the opening and even with the finished floor of the kitchen. This will facilitate removal of the dishwasher at a later date for service, if needed. • The dishwasher must be installed no more than 10 feet from sink for proper drainage. • The dishwasher must be fully enclosed on the top, sides and back. • The dishwasher must not support any part of the enclosure. 3 Install...