Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
This symbol on the product or its packaging indicates that the product may not be treated as household waste. Instead it should be handed over your local community waste collection/ recycling centre. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. 1 2 Getting to Know Your Dishwasher Dishwasher Interior (Fig.2-1) Control Panel (Fig.2-2) 2. Overview and Operation ArtNo.800-0108 - RDW6012 annotated P 12 6h 4h 2h .. .. .. .. .. .. .. .. .. .. .. A Upper rack .. B Upper spray arm C Lower rack D Cutlery basket E Control panel F Lower spray arm G Salt container cap H Washing fi lter I Detergent and rinse aid dispenser J Water inlet hose K Drain hose L Power supply cord Fig.2-1 P 12 6h 4h 2h .. .. .. .. .. .. .. .. .. .. A ON-OFF button B ON-OFF indicator C . load button D Programmes button E Programme indicator F Low salt indicator G Low rinse aid indicator H . load indicator light I Delay indicator lights J Delay start button Fig.2-2 DocNo.800-0201 - Overview - R6012 dishwasher Salt The hardness of water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the salt into the container Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: 1. When the low salt indicator (Fig.2-3) lights, you must fill the salt. Remove the lower rack and then unscrew and remove the cap from the salt container. Note: If you are filling the container for the first time, fill it with water 2. Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. 3. Carefully screw the cap back on. IMPORTANT: To prevent the formation of rust, load the salt just before beginning a wash cycle. Adjusting salt consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimize and customize the level of salt consumption so that it remains at a minimum. To adjust salt consumption: 1. Unscrew the cap from the salt container. 2. There is a ring on the container with an arrow on it (Fig.2-4). 3. If necessary, rotate the ring in an anticlockwise direction from the ‘–‘ setting towards the ‘+’ sign, based on the hardness of the water being used. It is recommended that adjustments be made in accordance with Table 2-1. Water Hardness Level Clarke degrees °dH mmol/l Selector position Salt consumption cycle Autonomy (cycles/ 2kg) 1 0 - 14 0 -17 0 - 1.7 0 2 14 -36 18 - 44 1.8 - 4.4 – 20 60 3 36 -71 45 - 89 4.5 - 8.9 MED 40 40 4 > 71 > 89 > 8.9 + 60 25 Table 2-1 Fig.2-3 Fig.2-4 3 .... Fig.2-5 Fig.2-6 Fig.2-7 Fig.2-8 Fig.2-9 .... Fig.2-5 Fig.2-6 Fig.2-7 Fig.2-8 Fig.2-9 Rinse Aid This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the door. When the low rinse aid indicator (Fig.2-5) lights you must add rinse aid. Loading the rinse aid To load the rinse aid: 1. To open the dispenser, turn the cap in an anti-clockwise direction and remove (Fig.2-6). 2. Pour in the rinse aid, making sure not to overfill. Regulate the amount of rinse aid used for each cycle by turning the dose adjuster (Fig.2-7), located beneath the cap, with a screwdriver. There are 6 different settings the normal dosage setting is 3. IMPORTANT: Proper dosage of rinse aid improves drying. If drops of water remain on the dishes or spotting occurs, the dosage adjuster should be turned to a higher setting. If the dishes have white streaks, turn the adjuster to a lower setting. Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the ‘Programme overview’. The detergent dispenser is located on the inside panel of the door. Loading the detergent To load the detergent: 1. Open the cover on the dispenser by pressing the button (Fig.2-8). 2. Pour the detergent for the wash cycle into compartment ‘A’ (Fig.2-9). 3. Pour the detergent for the prewash cycle into compartment ‘B’ (Fig.2-9). 4. After the detergent has been placed in the dispenser, close the cover and press down until it clicks in place. Note: To allow the cover to close properly, remove any excess detergent from the edges of the dispenser. DO NOT use 3-in-1 or similar tablets when Heat . Wash, Rapid Wash and Soak programmes are selected. 4 Detergent tablets explained Classi...
Dieses Handbuch ist für folgende Modelle:Geräte - RDW6012FI (917.8 kb)