Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1.Open the door carefully. The dishwashing cycle will stop. 2.Close the door. The cycle will continue. Aborting the dishwashing cycle 1.Press function buttons 2 and 3 and keep them pressed. The programme display for the current cycle will flash for several seconds and then go out. 2.Release the function buttons. The dishwashing cycle has been cancelled. 3.If you want to start a new cycle, check whether there is any detergent in the dispenser. 3 Turning off the dishwasher will only interrupt a selected dishwashing cycle, not cancel it. The cycle will recommence after turning the dishwasher back on again. Setting the Delay Timer Using the delay timer you can delay the start of a dishwashing cycle for 3, 6 or 9 hours. 1.Press the ON/OFF button. Press the Delay Timer button repeatedly until the indicator next to the number of hours for which the start of the dishwashing cycle is to be delayed lights up, e. g. 6h, if the cycle is to start in 6 hours. 2.Select dishwashing cycle. The LED indicator for the programme selected and the indicator next to the number of hours will light up. The dishwashing cycle will start automatically following a countdown of the hours set. To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. Cancelling the delay timer: Press the DELAY TIMER button repeatedly until none of the three time displays is lit. The selected dishwashing cycle will begin immediately. To change a dishwashing cycle As long as the cycle has not yet started, you can still change the dish- washing cycle. First abort the dishwashing cycle, then re-set the time delay, lastly select the new dishwashing cycle. Switching off the dishwasher Do not switch off the dishwasher until the indicator for the end of the dishwasher cycle is illuminated in the cycle progress display. With some dishwashing cycles, the drying fan continues to run even after the end of the cycle. 1.Press the ON/OFF button. All display indicators will go out. 2.Turn off the water tap. 1 Carefully open the door. Hot steam may escape. Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about 15 minutes before removing them. You also get a better drying result. Removing the dishes 3 It is normal for the inner door and the dispensers to be damp. • Empty the lower basket first, then the upper basket. This way you avoid dripping water from the upper basket onto dishes in the lower basket. Care and cleaning 1 Do not use furniture care products or aggressive cleaners. • When necessary, clean the dishwasher’s controls with a soft cloth and clean warm water. • Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the filters 3 The filters must be regularly checked and cleaned. Dirty filters will spoil the wash results. 1.Open the door and remove the lower basket. 2.Turn the handle about . of a turn anticlockwise (A) and remove the filter system (B). 3.Take hold of the coarse and fine filters (1/2) by the handle and remove them from the micro-filter (3). 4.Clean all filters thoroughly under running water. 5.Remove the flat filter (4) from the base of the washing compartment and clean both surfaces thoroughly. 6.Re-insert the flat filter. 7.Place the coarse and fine filters in the micro-filter and press together. 8.Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not protrude above the base of the washing compartment. 1 Under no circumstances may the dishwasher be used without its filters. What to do if... Remedying small malfunctions If while the appliance is operating indicators on the control panel flash or are lit up as described in the following table, please consult this to find out how to remedy the fault. After remedying the fault that is flashing in the first or second rhythm in the programme progress display, press the button for the dishwashing cycle that had already started. The cycle will continue. If the fault is displayed again or if other faults are displayed, please contact the Customer Care Department and inform them of the fault display. Malfunction Possible cause Remedy The programme indicator for the selected dishwashing cycle is flashing, the indicator for the end of the dishwashing cycle is flashing in rhythm 1 short light signal with approx. 3 second pause in-between: There is no water entering the dishwasher. The programme indicator for the selected dishwashing cycle is flashing, the indicator for the end of the dishwashing cycle is flashing in rhythm 2 short light signals one after another. The tap is blocked or furred Clean tap. with lime-scale. The tap is turned off. Turn the tap on. The filter (where present) in Clean the filter in the the threaded hose fitting on threaded hose fitting. the tap is blocked. Filters in the base of the washing compartment are blocked. Pr...