Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
.HygienePlus * This function increases the temperatures and retains them for an extra long time to obtain a defined disinfection performance. Continuous use of this function increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. I Intensive zone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. i High gloss drying * By increasing the amount of water during the rinse cycle and extending the drying phase, stains are prevented and the drying result is improved. There is a slight increase in the energy consumption. Rinse aid is recommended for the high gloss drying function (even when using combination detergents). . Energy Save * Water and energy consumption can be reduced with the “Energy Save” function. The running time is extended for optimum cleaning and drying results. 1 Operating the appliance Programme data The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result in deviations. Opening the doors To open the door, press the upper middle part of the door. The appliance opens automatically. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Operating the appliance en Zeolith drying The appliance features a Zeolith container Zeolith is a mineral which can store moisture and heat energy and release them again. During the washing step this heat energy is used to dry the mineral and heat up the rinsing water. During the drying phase moisture from the washing compartment is stored in the mineral and heat energy is released. This released heat energy is blown into the washing compartment with dry air. This accelerates and improves drying. These processes therefore save a great deal of energy. a Caution Please ensure that the intake opening 1J is not obstructed and do not place any temperature-sensitive utensils in the lower basket at the rear right side above the blow opening 1R. a Warning – Risk of injury! Do not touch the blow opening 1R. The blow opening becomes hot and, furthermore, any damage will result in a chargeable callout by customer service. en Operating the appliance Switching on the appliance 1. Turn on the tap fully. 2. Open the door. 3. Switch on ON/OFF switch (. The Eco 50° programme display flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display 8. 4. Press the START button )". 5. Close the door. The programme starts running. Note -for environmentally friendly operation of the dishwasher: For ecological reasons the Eco 50° programme is preset whenever the appliance starts. This conserves environmental resources and not least saves you money. The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils. Optical display while the programme is running * * depending on model While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor. If the door is not completely closed, the light spot flashes. * If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. This function can be changed as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button )" until •:‹.... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display 8 displays the factory setting •:‹…. 5. Press programme button # until the factory set value ‚:‹‚ is indicated on the digital display 8. To change the setting: 1. By pressing the button 3, you can switch the function off ‚:‹‹ or on ‚:‹‚. 2. Press START button )". The set value is saved. 3. Close the door. Operating the appliance en Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on...
Dieses Handbuch ist für folgende Modelle:Geräte - SBE69U11EU/74 (2.26 mb)
Geräte - SBE69U11EU/76 (2.26 mb)