Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. m Warning – Health hazard Never use other domestic detergents, e.g. containing chlorine! Special salt and rinse aid . Check the refill indicators ` and X. If required, refill salt and/or rinse aid. en Cleaning and maintenance Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arms 1: (1/4 revolution). and take out filter system. 3. Remove the lower spray arm 1B upwards. 3.Remove any residue and clean filters under running water. 4.Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. ........ 4.Clean spray arms under running water. 5.Re-engage or screw on spray arms. 3 Fault, what to do? Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Operating the appliance”) m Warning – Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. m Warning – Risk of cuts! When cleaning the waste water pump, ensure that you do not injure yourself on pieces of broken glass or pointed implements. Fault, what to do? en In this case: 1. First always disconnect the appliance from the power supply. 2. Take out top basket 1" and bottom basket 1b. 3. Remove the filters 1R. 4. Scoop out water, use a sponge if required. 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely. .. 6. Check impeller wheel and remove any foreign objects. 7. Place cover in the original position and press down until it engages (click). .............. 8.Install filters. 9.Re-insert baskets. en Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display hlights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Clean filter in the supply hose. Screw water connection on again. Check for leaks. Reconnect power supply. Switch on the appliance. Filters 1R are soiled or Clean filters. blocked. (See Cleaning and maintenance) Waste water hose Install hose without kinks, remove any is blocked or kinked. residue. Siphon connection still sealed. Check connection to siphon and open if required. Waste water pump blocked Lock cover correctly. or cover on the waste water pump is not locked in position. (See Waste water pump) Display “Check water A technical fault has probably Switch off appliances with the ON/OFF supply” hflashes. occurred. switch (. After a short time restart the appliance. If the problem recurs, turn off the tap, pull out the mains plug and call customer service. Displays flash. Door not closed properly. Close the door. Ensure that no objects (utensil, fragrance dispenser) are protruding over the basket and preventing the door from closing. Fault, what to do? en Fault Cause Remedial action Refill indicator for salt ` and/or rinse-aid Xis lit. No rinse aid. No salt. Sensor does not detect salt tablets. Refill rinse aid. Refill with special salt. Use different special salt. Refill indicator for salt ` and/or rinse-aid X is not lit. Refill indicator switched off. There is still enough special salt/ rinse aid available. Activation/deactivation (see chapter Water softening system/Special salt or Rinse aid). Check refill indicator, levels. Water is left in the appliance at the end of the programme. Filter system or area under the filters 1R is blocked. The programme has not yet ended. Clean filters and area ...
Dieses Handbuch ist für folgende Modelle:Geräte - DRS4302/14 (1.35 mb)
Geräte - DRS4308/10 (1.35 mb)
Geräte - DRS4308/14 (1.35 mb)