Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Dishes tends to chip if removed still hot from the dishwasher. ^ Let the dishware cool by opening the door slightly. The dishes will cool much faster. ^ Open the dishwasher and unload the dishes. ^ Turn the dishwasher off s. The dishwasher continues to use electricity until turned off with the s button. ^ If the dishwasher is not used for a longer period of time, e.g. vacationing, turn off the water supply. Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. ,Open the door with care. The water in the dishwasher is hot. Danger of scalding. Before closing the door again, leave it ajar for approx. 20 secs. This will enable the temperature in the wash cabinet to settle. Close the door firmly until it clicks into place. Changing a program If the detergent flap is already open do not change the program. If a program has already started and you wish to change it: ^ Press the "Start/Stop" button for at least one second. The program is cancelled. The "Start/Stop" indicator lights. ^ Select and start the desired program. Additional functions Factory default All settings can be reset to the factory default. ^ Turn the dishwasher off s. ^ Press the "Start/Stop" button and at the same time turn the dishwasher on s. Hold the "Start/Stop" button until the "Start/Stop" indicator comes on. If it does not come on, start over. ^ Press the program button 12 times. The bottom program indicator flashes once long and twice short in intervals. The "Rinse" indicator shows if a setting was changed. – The "Rinse" indicator flashes: All settings are the factory default. – The "Rinse" indicator is off: At least one setting was changed. ^ To reset the dishwasher to the default settings, press the "Start/Stop" button. ^ Turn the dishwasher off s. Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Issue Possible fault Solution The Start/Stop indicator does not flash after the dishwasher is turned on with s. The machine is not plugged in. Insert the plug. The fuse has tripped. Reset the circuit breaker. Make sure it is a 15 A breaker. The dishwasher stops during a program. The fuse has tripped. Reset the circuit breaker. Make sure it is a 15 A breaker. The program cycle There may be a technical – Turn the dishwasher off indicators "Rinse", fault. s. "Drying" and "End" After a few seconds: flash at the same time. – Turn the dishwasher on. – Select the desired program with the program selector button. – Press the "Start/Stop" button. If the problem persists, call Technical Service. The drain pump is running when the door is open. The waterproof system has activated. – Turn off the water supply. – Call Miele Technical Service. Frequently asked questions Problems water intake/drain Issue Possible fault Solution The "Intake/Drain" indicator flashes and lights alternately. The water supply is closed. Open the water supply all the way. The dishwasher stops running. The "Intake/Drain" indicator flashes. Before fixing the fault: – Turn the dishwasher off s. Fault in the water intake. – Open the water supply all the way. – Clean the water intake filter, see "User Maintenance Instructions". – The water pressure at the water connection is lower than 4.35 psi. Consult a plumber. Fault in the water – Clean the triple filter. drain. – Clean the drain pump and There may be water in the non-return valve. the wash cabinet. See "User Maintenance Instructions" for more information on the above. – Remove any kinks in the drain hose. Frequently asked questions General problems with the dishwasher Issue Possible fault Solution Detergent is left in the dispenser at the end of a program. The dispenser was damp when detergent was added. Dry the dispenser before adding detergent. The detergent lid cannot be closed properly. Detergent residue is blocking the catch. Remove the residue. The door and the interior walls are still wet after a program has finished. This is not a fault! It is the normal operating mode of the drying system. The moisture will evaporate after a short time. Water remains in the wash cabinet at the end of a program. Before fixing the fault: – Turn the dishwasher off s. The triple filter in the wash cabinet is clogged. Clean the triple filter. See "User Maintenance Instructions". The drain pump or the non-return valve may be blocked. Clean the drain pump and the non-return valve, see maintenance instructions. The drain hose is kinked. Remove any kinks from the drain hose. Frequently asked questions Sounds Issue Possible fault Solution There is a knocking noise in the wash cabinet. The spray arm is hitting an item in the basket. Interrupt the program, rearrange items bl...