Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Optical display while the programme is running * * depending on model While the programme is running, an optical display is indicated on the floor under the appliance door. If the base panel is pulled forwards or if the appliance is installed at eye- level with flush furniture front, the display is not visible. Possible settings of the optical display: †:‹‹ The display is switched off. †:‹‚ Programme, timer programming, remaining time, end of programme and, if required, low water level are displayed. †:‹. Same as †:‹‚. Other programme information is also displayed, e.g. the symbol for half load § or glass protection system active W. †:‹‚ is set at the factory. en Operating the appliance To change the setting: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. 4. Release both buttons. The illuminated display of the button # flashes. 5. Keep pressing programme button # until the previously set value, e.g. †:‹‚, is indicated on the digital display h †:‹... (for the optical display). 6. Keep pressing programme button 3 until the required value, e.g. †:‹., is indicated on the digital display h. 7. Press START button `. The set value is saved. 8. Close the door. Remaining running time display When the programme is selected, the programme running time is indicated on the digital display h. When the programme has started, the remaining running time is displayed on the floor (only for settings †:‹‚ and †:‹.). The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. 1. Open the door. 2. Switch on ON/OFF switch (. 3. Press button P + until the digital display h jumps to oe:‹‚. 4. Press P + or – button until the displayed time corresponds with your requirements. 5. Press START button `, timer programming is activated. 6. To delete timer programming, press the P + or – button until h oe:‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. 7. Close the door. End of programme The end of the programme O / ‹:‹‹ is displayed on the floor – provided the optical display is switched on and is visible. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. 5. Press programme button # until the factory set value ›:‹. is indicated on the digital display h. Operating the appliance en To change the setting, 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off). 2. Press START button `, the set value is saved. 3. Close the door. Note Depending on the setting for “Automatic switch off when programme ends or interior light”, the optical display is no longer or only briefly visible. Automatic switch off after end of programme or interior light* * depending on model To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends. The setting can be selected from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically. The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed the light is off. If the door is open for longer than 60 min., the light switches off automatically. The interior light 1" is lit only when the set value .:‹‹ is selected. .:‹‚ Appliance switches off after 1 min. .:‹. Appliance switches off after 120 min. 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. 5. Keep pressing programme button # until the value .:‹... is indicated on the numerical display h. To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹. 2. Press START button `. The set value is saved. 3. Close the door. Switching off the appliance Short time after the end of the programme: 1. Open the door. 2. Switch off ON/OFF switch (. 3. Turn off the tap (not applicable if Aqua-Stop fitted). 4. Remove the utensils when they have cooled down. Note When the programme ends, leave the appliance to cool down a while before opening ...
Dieses Handbuch ist für folgende Modelle:Geräte - S58T69X3EU/14 (1.39 mb)